Whirlpool WDE150LVS User Manual
Page 3
3
Mobile Home - Additional Installation Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD Part 280). When such standard is not
applicable, the Standard for Manufactured Home Installations,
ANSI A225.1/NFPA 501A or with local codes.
Mobile home installations require:
■
When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the standards
listed above.
■
Four-wire cable must be used in a mobile home installation.
The appliance wiring will need to be revised. See “Electrical
Connection” section.
Product Dimensions
*Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.
**When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm)
countertop; front of oven door protrudes 2
¹⁄₂" (6.4 cm) beyond
24" (61 cm) base cabinet.
Cabinet Dimensions
Cabinet opening dimensions shown are for 25" (64 cm)
countertop depth, 24" (61 cm) base cabinet depth and
36" (91.4 cm) countertop height.
IMPORTANT: If installing a range hood or microwave hood
combination above the range, follow the range hood or
microwave hood combination installation instructions for
dimensional clearances above the cooktop surface.
*NOTE: 24" (61 cm) minimum when bottom of wood or metal
cabinet is covered by not less than
¹⁄₄" (0.64 cm) flame
retardant millboard covered with not less than No. 28 MSG
sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm)
aluminum or 0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the
cooking platform and the bottom of an uncovered wood or
metal cabinet.
**The plywood support (J) is required only when the wall
mounting option is chosen for installation of the anti-tip
bracket. For more information, see the “Install Anti-Tip
Bracket” section.
A.
30³⁄₄" (78 cm)
B. 27
¹⁄₂" (69.9 cm) height to underside
of cooktop edge with leveling legs
screwed all the way in*
C. Model/serial number plate
(located below the electronic
control on oven frame)
D. 29
⁷⁄₈" (75.9 cm)
E. 28
⁵⁄₁₆" (71.9 cm) from
handle to standoff at back
of range**
F. 23
³⁄₄" (60.3 cm)
countertop notch to rear
of cooktop
C
B*
A
D
E**
F
A. 13" (33 cm) upper cabinet depth
B. 30" (76.2 cm) min. opening width
C. For minimum clearance to the top
of the cooktop, see NOTE*.
D. 23
¹⁄₄" (58.1 cm) opening depth
E.
30" (76.2 cm) min. opening width
F. Junction box - 5.5" (14 cm) min.
from either cabinet, 8
¹⁄₄" (21 cm)
max. from floor
G. Cabinet door or hinge should
not extend into cutout.
H. 27
¹⁄₂" (69.9 cm) top of
countertop to support slats
I. 6" (15.2 cm) wide support
slat on each side of cutout
J. (Optional) -
³⁄₈
" (1.0 cm)
plywood support (30"
[76.2 cm] width x 4"
[10.2 cm] height), securely
attached to at least 2 wall
studs, in place of sheetrock**
A
B
C
D
E
F
G
H
I
J**