Liebherr CBNPes 3967 PremiumPlus BioFresh NoFrost - Manual (Page 11)

u On the upper door, rotate the turn hinge Fig. 20 (23)
outwards, parallel to the edge of the door.
Fig. 21
NOTICE
Cables may be twisted and damaged as a result!
u Use the template.
u Detach the supplied template Fig. 21 (61) from the turn
hinge and use it to prevent the turn hinge Fig. 21 (23) and
bush from turning.
u Using a screwdriver, push out the turn
hinge Fig. 20 (23) from underneath and
remove it from the door, complete with
cable.
u Using a screwdriver, push out the stopper
Fig. 20 (62) from underneath and transfer it
to the opposite side.
u Thread in the cable of the turn hinge Fig. 20 (23) on the
opposite side and insert the turn hinge.
u Detach the template Fig. 20 (61) and secure it in the turn
hinge.
u Plug in the connector Fig. 20 (60) .
u Lay the cable in the guide.
Appliances without soft stop mechanism:
u Snap the cover Fig. 20 (63) into place on the door.
4.3.13 Fitting the upper door
u Place the upper door on the middle bearing pin Fig. 13 (41) ,
close the door and attach the upper turn hinge Fig. 10 (23)
so that it engages in the upper side of the appliance.
u Screw theturn hinge Fig. 10 (23) firmly into place (with
4 Nm). Possibly make preliminary holes with a bradawl or
use a cordless screwdriver.
u Snap cover Fig. 10 (20) and cover Fig. 10 (21) into place.
u Plug in the connector Fig. 8 (12) again.
u Lay the cable in the guide.
u Attach the cover Fig. 8 (10) again.
Appliances without soft stop mechanism:
u Turn the cover Fig. 9 (6) through 180°, attach it from the
outside to the handle side and snap it into place.
u Turn the cover Fig. 9 (11) through 180°, attach it from the
outside to the handle side and snap it into place.
Appliances with soft stop mechanism:
u Leave the door open.
4.3.14 Fitting the upper soft stop mechanism*
For appliances with soft stop mechanism.
For appliances without soft stop mechanism proceed with
item (see 4.3.15) .
Fig. 22
u Remove the cover Fig. 22 (9) from the faceplate Fig. 22 (1)
and re-insert it at the other side.
u Engage the upper soft stop unit with the joint on the hinge
side (A) and swivel into place (B).
w The screw holes at the left and right have to register.
u Screw the soft stop unit firmly into place. (2x Torx® 15)
Fig. 22 (7)
Note
u Keep to the correct order. First attach the panel over the soft
stop bracket, then the cover.
Fig. 23
u Attach the faceplate Fig. 23 (1) to the soft stop bracket
Fig. 23 (4) so that the catches face inwards and the front
faces the appliance.
u Slide on the cover Fig. 23 (5) from the outside (A) and swivel
it over the bearing element Fig. 23 (8) (B).
u Attach the cover Fig. 23 (5) and engage it as far as the first
detent.
w The openings for the pin are on top of one another after the
soft stop bracket has been positioned.
u Draw the soft stop bracket Fig. 23 (4) to the bearing element
Fig. 23 (8) and insert the pin Fig. 23 (4) from above so that
the square is seated in the depression.
u Now completely snap the cover Fig. 23 (5) onto the bearing
element Fig. 23 (8) .
w Pay attention that the cover fits properly so that the door
closes properly and the pin is secured.
u Twist the safety lock Fig. 23 (2) for removal.
u Snap thefaceplate Fig. 23 (1) onto the door.
u Turn the cover Fig. 6 (6) through 180°, attach and engage it
on the handle side.
4.3.15 Aligning the doors
u Possibly align the door to the appliance housing by way of
the two slots in the lower turn hinge Fig. 15 (55) and middle
turn hinge Fig. 13 (42) . To do so, unscrew the middle screw
in the bottom turn hinge Fig. 15 (55) .
Putting into operation
* Depending on model and options 11