Liebherr CBNPes 3967 PremiumPlus BioFresh NoFrost - Manual (Page 21)

Switching off the IceMaker
u
Activate the MAIN MENU.
u Activate the FREEZER -> ICEMAKER -> OFF menu items
one after the other.
w The IceMaker is switched off.
Producing ice cubes
The production capacity depends on the freezer temperature.
The lower the temperature, the more ice cubes can be
produced in a specific period.
The ice cubes drop from the IceMaker into the drawer. When a
certain filling level has been reached, no further ice cubes are
produced. The IceMaker does not fill the drawer right up to the
brim.
If large quantities of ice cubes are needed, the complete
IceMaker drawer can be exchanged for the adjacent drawer.
When the drawer is closed, the IceMaker automatically re-
commences production.
Once the IceMaker has been switched on for the first time, it
may take up to 24 hours until the first ice cubes are produced.
Note
When the appliance is used for the first time and if it has been
out of use for a long time, particles may collect in the IceMaker
and/or water conduit.
u Therefore do not use or consume the ice cubes made in the
first 24 hours.
Adjusting the water intake time
The opening time of the IceMaker valve can be adjusted if, for
example, the water pressure in the line is too low or too high.
The water intake time is adjustable in steps from E1 (short
intake time) to E8 (long intake time). If the intake time is too
long, then e.g. large ice cubes or a block of ice may form, in
which case reduce the intake time.
Fig. 36
u Activate the MAIN MENU.
u Activate the FREEZER -> ICEMAKER -> WATER INTAKE
menu items one after the other.
u To decrease the water intake time: Press Up button
Fig. 36 (6) .
-or-
u To increase the water intake time: Press Down button
Fig. 36 (7) .
6 Maintenance
6.1 Defrosting with NoFrost
The NoFrost system automatically defrosts the appliance.
Refrigerator compartment:
The defrost water evaporates due to the compressor heat.
u Regularly clean the drain opening to allow the water to flow
away (see 6.2) .
Freezer compartment:
The moisture condenses on the evaporator, is periodically
defrosted and evaporates.
u The appliance does not have to be manually defrosted.
6.2 Cleaning the appliance
WARNING
Risk of injury and damage as a result of hot steam!
Hot steam can lead to burns and can damage the surfaces.
u Do not use any steam cleaners!
NOTICE
Incorrect cleaning damages the appliance!
u Do not use cleaning agents in concentrated form.
u Do not use any scouring or abrasive sponges or steel wool.
u Please do not use any aggressive, scouring, sand-,
chloride-, chemical- or acid-based cleaning agents.
u Do not use chemical solvents.
u Do not damage or remove the type plate on the inside of the
appliance. It is important for the customer service.
u Do not pull off, bend or damage cables or other compo-
nents.
u Do not allow any cleaning water to enter the drain channel,
ventilation grille or electrical parts.
u Please use soft cleaning cloths and a universal pH-neutral
cleaning agent.
u Please use cleaning and care products suitable for contact
with foodstuffs in the appliance interior.
u Empty appliance.
u Pull out the power plug.
u Clean plastic outer and inner surfaces with lukewarm
water and a little washing-up liquid.
NOTICE
The stainless steel doors are provided with a high-quality
surface coating and must not be treated using the accompa-
nying care product.
Otherwise the surface coating will be affected.
u Wipe the coated door surfaces using a soft, clean cloth
only. In case of stubborn dirt, use a little water or a neutral
cleaning agent. A microfibre cloth can be optionally used.
u If the stainless steel side walls are dirty, clean them using
a commercially available stainless steel cleaning agent.
Then evenly apply the accompanying stainless steel care
product, making strokes in the direction of the grain.
u Wipe side walls with a paint finish using a soft, clean
cloth only. In case of stubborn dirt, use a little water or a
neutral cleaning agent. A microfibre cloth can be optionally
used.
u Clean drain hole: Remove deposits
with a narrow instrument, e.g. a
cotton bud.
u Most of the parts can be dismantled for cleaning: see the
relevant chapter.
u Clean items of equipment by hand with lukewarm water
and a little washing-up liquid.
u Only use a damp cloth to clean the telescopic rails. The
grease in the runners is for lubrication purposes and must
not be removed.
After cleaning:
u Wipe dry the appliance and items of equipment.
u Connect the appliance and switch it on again.
Maintenance
* Depending on model and options 21