Liebherr CBNPes 3967 PremiumPlus BioFresh NoFrost - Manual (Page 7)

q
Always stand the appliance backed directly to the wall using
the enclosed wall spacers (see below).
q
The appliance may be moved only when it is empty.
q Do not install the appliance without assistance.
q The more R 600a refrigerant there is in the appliance, the
larger the room in which the appliance is standing needs to
be. In rooms that are too small, a flammable mix of gas and
air may be created if there is a leak. According to the EN
378 standard, every 11 g of R 600a refrigerant requires at
least 1 m 3 space in the room for the appliance. The amount
of refrigerant in your appliance is on the type plate inside the
appliance.
u Detach the connecting cable from the rear of the appliance,
removing the cable holder at the same time because other-
wise there will be vibratory noise!
u Remove the protective film from the outside of the appli-
ance.
NOTICE
The stainless steel doors are provided with a high-quality
surface coating and must not be treated using the accompa-
nying care product.
Otherwise the surface coating will be affected.
u Wipe the coated door surfaces using a soft, clean cloth
only.
u Apply a stainless steel cleaner only to the stainless steel
side walls evenly, wiping with the grain. Subsequent
cleaning becomes easier as a result.
u Wipe side walls with a paint finish using a soft, clean
cloth only.
u Remove the protective film from the decorative trims and
drawer fronts.
u Remove all transit supports.
The spacers supplied with some appliances must be used to
achieve the stated energy consumption. These will extend the
depth of the appliance by approx. 35 mm. The appliance is fully
functional if the spacers are not used, but does have a slightly
higher energy consumption.
u In the case of an appliance with
enclosed wall spacers, mount the
wall spacers on the back of the
appliance at the top left and right.
u Dispose of packaging material (see 4.6) .
u Align the appliance so that it
stands firmly and on a level by
applying the accompanying
spanner to the adjustable-
height feet (A) and using a
spirit level.
u Then support the door: Extend
the adjustable foot at the turn
hinge (B) until it rests on the
floor and then make a further
90° turn.
Note
u Clean the appliance (see 6.2) .
If the appliance is installed in a very damp environment,
condensate may form on the outside of the appliance.
u Always see to good ventilation at the installation site.
4.3 Changing over the door hinges
You can change over the door hinges if necessary.
Ensure that the following tools are to hand:
q
Torx® 25
q Torx® 15
q Screwdriver
q Cordless screwdriver, if necessary
q
Second person for fitting work, if needed
4.3.1 Detaching the upper soft stop mecha-
nism*
For appliances with soft stop mechanism start with this item.
For appliances without soft stop mechanism start with item
(see 4.3.2) .
Fig. 4
u Open the upper door.
NOTICE
Risk of damage!
If the door seal is damaged, the door may fail to close properly
and the cooling will be inadequate.
u Do not damage the door seal with the screwdriver!
u Disengage and remove the faceplate Fig. 4 (1) using a flat-
blade screwdriver.
w The faceplate is attached over the soft stop bracket.
Fig. 5
u Push the faceplate over the soft stop bracket Fig. 5 (4) in the
direction of the appliance.
u Snap the safety lock Fig. 5 (2) into the oblong hole.
w The safety lock prevents the hinge from snap-closing.
u Using a screwdriver, disengage the cover on the hinge side
Fig. 5 (5) as far as the first detent.
w The pin becomes visible.
u Press the pin Fig. 5 (3) out from underneath.
u Press the soft stop bracket Fig. 5 (4) towards the door.
u Fully detach the cover on the hinge side Fig. 5 (5) and
remove it.
Putting into operation
* Depending on model and options 7