Liebherr CBNPes 3967 PremiumPlus BioFresh NoFrost - Manual (Page 9)

Fig. 12
u Slide the faceplate forwards over the soft stop bracket
Fig. 12 (34) in the direction of the appliance.
u Snap the safety lock Fig. 12 (32) into the oblong hole.
w The safety lock prevents the hinge from snap-closing.
u Using a screwdriver, lift off the cover Fig. 12 (31) from the
outside and remove it in an outward direction.
u If necessary, tip the appliance backwards with the assis-
tance of a second person.
u Press the pin Fig. 12 (33) out from underneath.
u Press the soft stop bracket Fig. 12 (34) towards the door.
u Remove the faceplate Fig. 12 (30) .
u Unscrew the soft stop unit (2x Torx® 15) Fig. 12 (35) .
u Pull the soft stop unit out a little, push it in the direction of the
handle side and swing it out.
u Set the soft stop unit aside.
4.3.5 Detaching the lower door
u Close the lower door.
For appliances without soft stop mechanism:
u Draw the middle bearing pin Fig. 13 (41) out of the turn
hinge and lower door.
For appliances with soft stop mechanism:
u Draw the middle bearing pin Fig. 13 (41) together with the
washer Fig. 13 (44) out of the turn hinge and lower door.
For all appliances:
u Remove the plastic cap Fig. 13 (40) .
CAUTION
Risk of injury if the door tips!
u Take good hold of the door.
u Set down the door carefully.
u Open the lower door.
u Unscrew the middle turn hinge (2x Torx® 25). Fig. 13 (42)
u Lift off the lower door and set it aside.
4.3.6 Transferring the middle bearing elements
Fig. 13
u Carefully detach the cover panel Fig. 13 (43) .
u Turn the middle turn hinge Fig. 13 (42) with thewasher
Fig. 13 (45) through 180° and screw it firmly into place on
the new hinge side (with 4 Nm).
u Turn the cover panel Fig. 13 (43) through 180° and snap it
into place again on the new handle side.
4.3.7 Transferring the lower bearing elements*
for appliances without soft stop mechanism
Fig. 14
u Lift out the bearing pin Fig. 14 (52) together with washer
Fig. 14 (53) and adjustable-height foot Fig. 14 (54) .
u Lift off the stopper Fig. 14 (51) .
u Unscrew Fig. 14 (56) the turn hinge Fig. 14 (55) .
u Unscrew Fig. 14 (59) the bearing element Fig. 14 (58) ,
transfer it to the opposite location hole of the turn hinge and
screw it firmly into place.
u Carefully lift off the cover on the handle side Fig. 14 (57) and
transfer it to the opposite side.
u Screw the turn hinge Fig. 14 (55) firmly into place on the
new hinge side, possibly using a cordless screwdriver (with
4 Nm).
u Re-insert the stopper Fig. 14 (51) into the other hole.
u Re-insert the bearing pin Fig. 14 (52) together with the
washer and adjustable-height foot. In so doing, pay attention
that the locating lug points backwards
4.3.8 Transferring the lower bearing elements *
for appliances with soft stop mechanism
Fig. 15
u Lift out the bearing pin Fig. 15 (52) together with washer
Fig. 15 (45) and adjustable-height foot Fig. 15 (54) .
u Lift out the stopper Fig. 15 (51) .
Putting into operation
* Depending on model and options 9