Sp-pb140 eng_manual 17.pdf, Operation, Using the redeye laser line generator – Steele Products SP-PB140 User Manual
Page 17
17
Operation
p fence, miter gauge and upper blade guide as
ir
,
e
l
g
n
a
l
e
v
e
b
e
h
t
t
s
u
j
d
A
.
1
required.
t is in place and flush with the table.
r
e
s
n
i
e
l
b
a
t
e
h
t
t
a
h
t
e
r
u
s
n
E
.
2
/
n/off switch to the ‘ON’ position.
o
e
h
t
h
s
u
p
w
a
s
e
h
t
tr
a
t
s
o
T
.
3
e wood into the moving saw blade.
h
t
e
d
i
u
g
t
u
c
e
h
t
n
i
g
e
b
o
T
.
4
o keep the saw cutting. Do not force the
t
e
r
u
s
s
e
r
p
h
g
u
o
n
e
y
l
n
o
e
s
U
.
5
cutting, allow the blade and the saw to do the work.
e ensure that the rip fence is located on the
l
g
n
a
l
e
v
e
b
a
n
o
g
n
it
t
u
c
n
e
h
W
.
6
right hand side of the blade.
r fixture to prevent the workpiece from turning.
o
g
ij
a
e
s
u
,
d
o
r
g
n
it
t
u
c
n
e
h
W
.
7
,use a suitable push block to feed the
y
ll
a
c
it
r
e
v
s
d
r
a
o
b
g
n
it
t
u
c
n
e
h
W
.
8
workpiece into the saw.
to the ‘OFF’
h
c
ti
w
s
f
f
o
/
n
o
e
h
t
g
n
i
h
s
u
p
y
b
l
o
o
t
e
h
t
ff
o
n
r
u
t
d
e
h
s
i
n
if
e
c
n
O
.
9
position and unplug the tool from the power point to prevent
unauthorized use.
Using the REDEYE laser line generator
WARNING.
Do not stare directly at the laser beam. Never aim the beam at
any person or an object other than the workpiece.Do not deliberately aim
the beam at personnel and ensure that it is not directed towards the eye
of a person.Always ensure the laser beam is aimed at a sturdy workpiece
without reflective surfaces. i.e. wood or rough coated surfaces are
acceptable. Bright shiny reflective sheet steel or the like is not suitable for
laser use as the reflective surface could direct the beam back at the operator.
Only turn the laser beam on when the work piece is on the tool.
1. Mark the line of cut on the work piece.
blade guide as required.
r
e
p
p
u
d
n
a
e
g
u
a
g
r
e
ti
m
,
e
c
n
e
f
p
ir
,
e
l
g
n
a
l
e
v
e
b
e
h
t
t
s
u
j
d
A
.
2
3. Switch on the laser beam using the laser light on/off switch.
4. Align the laser beam with the line on the work piece.
by adjusting the laser line. Loosen the laser
e
d
a
l
b
e
h
t
h
ti
w
l
e
ll
a
r
a
p
e
b
o
t
d
e
n
g
il
a
e
b
n
a
c
m
a
e
b
r
e
s
a
l
e
h
T
.
5
adjustment knob and move the laser beam until it is in line with the blade. Tighten the laser adjustment
knob.
6. To start the saw push the on/off switch to the ‘ON’ position.
7. To begin the cut guide the wood into the moving saw blade.
force the cutting, allow the blade and the saw
t
o
n
o
D
.
g
n
it
t
u
c
w
a
s
e
h
t
p
e
e
k
o
t
e
r
u
s
s
e
r
p
h
g
u
o
n
e
y
l
n
o
e
s
U
.
8
to do the work.
located on the right hand side of the blade.
s
i
e
c
n
e
f
p
ir
e
h
t
t
a
h
t
e
r
u
s
n
e
e
l
g
n
a
l
e
v
e
b
a
n
o
g
n
it
t
u
c
n
e
h
W
.
9
e workpiece from turning.
h
t
t
n
e
v
e
r
p
o
t
e
r
u
t
xi
f
r
o
g
ij
a
e
s
u
,
d
o
r
g
n
it
t
u
c
n
e
h
W
.
0
1
to feed the workpiece into the saw.
k
c
o
l
b
h
s
u
p
e
l
b
a
ti
u
s
a
e
s
u
,
y
ll
a
c
it
r
e
v
s
d
r
a
o
b
g
n
it
t
u
c
n
e
h
W
.
1
1
pressing the red ‘OFF’ button and unplug the
y
b
l
o
o
t
e
h
t
ff
o
n
r
u
t
,t
h
g
il
r
e
s
a
l
e
h
t
ff
o
n
r
u
t
d
e
h
s
i
n
if
e
c
n
O
.
2
1
tool from the power point to prevent unauthorised use.