JLG 120HX ANSI Service Manual - Manual (Page 36)

SECTION 2 - PROCEDURES
2-16 – JLG Lift – 3120686
NOTE: Self-locking setscrews used on piston nuts should be
discarded and replaced whenever they are removed.
8. If applicable, install the setscrew(s) which secure the
piston attaching nut to the diameter groove.
9. Remove the cylinder rod from the holding fixture.
10. Place new o-rings and seals in the applicable out-
side diameter grooves of both the piston and the cyl-
inder head.
11. Position the cylinder barrel in a suitable holding fix-
ture.
EXTREME CARE SHOULD BE TAKEN WHEN INSTALLING THE
CYLINDER ROD, HEAD, AND PISTON. AVOID PULLING THE ROD
OFF-CENTER, WHICH COULD CAUSE DAMAGE TO THE PISTON
AND CYLINDER BARREL SURFACES.
12. With barrel clamped securely, and while adequately
supporting the rod, insert the piston end into the
barrel cylinder. Ensure that the piston loading o-ring
and seal ring are not damaged or dislodged.
13. Continue pushing the rod into the barrel until the cyl-
inder head gland can be inserted into the barrel cyl-
inder or, if applicable, until the cylinder head threads
engage the threads of the barrel.
14. If applicable, secure the cylinder head retainer using
a suitable spanner type wrench in the holes pro-
vided.
15. After the cylinder has been reassembled, the rod
should be pushed all the way in (fully retracted) prior
to the reinstallation of any holding valve or valves.
16. If applicable, install the cartridge-type holding valve
and fittings in the rod port block using new o-rings
as applicable.
IF THE CYLINDER IS TO BE TESTED PRIOR TO INSTALLATION ON
THE MACHINE, EXTREME CARE SHOULD BE USED TO INSURE
THAT THE OUTER END OF THE ROD IS SUPPORTED. USE
EITHER A TRAVELING OVERHEAD HOIST, FORKLIFT, OR OTHER
MEANS TO SUPPORT THE OVERHANGING WEIGHT OF THE
EXTENDING ROD.
NOTE: Steps (17) through (20) apply to the telescope cylin-
der.
17. Elevate the barrel end of the cylinder to a work
bench or other suitable device.
18. Plug the retract port and supply hydraulic power to
the extend port.
19. Open the bleeder port plug (TP), venting all trapped
air to atmosphere. Retighten the bleeder port plug.
Disconnect the hydraulic power source and remove
plug from retract port.
20. An alternative to steps (18) through (20) is to posi-
tion the barrel horizontally in a suitable holding
device, attach a hydraulic power source to both
extend and retract ports, while supporting the cylin-
der rod, cycle the cylinder a minimum of 5 times with
Table 2-2. Cylinder Piston Nut Torque Specifications
Description
Nut Torque Value
(w/Loctite)
Setscrew Torque
Value (w/Loctite)
Axle Extension
Cylinder 400 ft. lb. (542
Nm)
100 in. lb. (11
Nm)
Extend-a-Reach
Cylinder 400 ft. lb. (542
Nm)
100 in. lb. (11
Nm)
Frame Jack
Cylinder 400 ft. lb. (542
Nm)
100 in. lb. (11
Nm)
Level/Slave
Cylinder 200 ft. lb. (271
Nm)
100 in. lb. (11
Nm)
Lift Cylinder 600 ft. lb. (813
Nm)
200 in. lb. (22
Nm)
Master Cylinder 80 ft. lb. (108 Nm) 100 in. lb. (11
Nm)
Steer Cylinder 80 ft. lb. (108 Nm) 100 in. lb. (11
Nm)
Telescope
Cylinder 600 ft. lb. (813
Nm)
200 in. lb. (22
Nm)
Table 2-3. Holding Valve Torque Specifications
Description Torque Value
Sun - 7/8 hex M20 x 1.5 thds 30-35 ft. lb.
(41-48 Nm)
Sun - 1-1/8 hex 1-14 UNS thds 45-50 ft. lb.
(61-68 Nm)
Sun - 1-1/4 hex M36 x 2 thds 150-160 ft. lb.
(204-217 Nm)
Racine - 1-1/8 hex 1-1/16 - 12 thds 50-55 ft. lb.
(68-75 Nm)
Racine - 1-3/8 hex 1-3/16 - 12 thds 75-80 ft. lb.
(102-109 Nm)
Racine - 1-7/8 hex 1-5/8 - 12 thds 100-110 ft. lb.
(136-149 Nm)