INCRA TS-II Table Saw Fence - Manual (Page 5)

Set final mounting bracket position
Clamp the (2) TS II base clamps to the front rail as
shown in Fig. 4 and loosen the bolts that secure the mount-
ing brackets to your table saw. The rail and mounting brack-
ets will drop down until the base clamps touch the top of
your saw, Fig. 5. This locates the final mounting bracket
position. Tighten the bolts that secure the mounting brackets
to your table saw. Repeat for the rear rail.
Mounting
bracket
FIG. 4
Set final mounting
bracket position
Base clamps
Clamp pad
Rail
Mounting
bracket
First: Clamp base clamps to
rail. Use clamp pads to avoid
marring anodized surfaces
Second: Loosen both mounting
bracket bolts. Brackets will lower slightly
Set final rail position
Loosen the bolts that secure the rails to the mounting
brackets and slide the rails so that they extend 7" beyond
the left hand extension wing of your table saw as shown in
Fig. 6. Push the rail against the short vertical leg on the
mounting bracket and tighten the bolts that hold the rail in
place. See Fig. 7 below.
5
4
5
Left hand extension wing
Short vertical leg
FIG. 5
Tighten
mounting
bracket
bolts
Base clamp
Table
saw
top
Mounting
bracket bolt
Mounting bracket is at
correct level when base
clamp touches table top
FIG. 6
Set final rail position
Rails should
extend 7" beyond
left hand exten-
sion wing
FIG. 7
Tighten rail
mounting
bolts
Push rail against
short vertical leg
and tighten rail
mounting bolts
7 "
Slide stop positioner and
base clamping knob assem-
blies onto the rails
Stop positioner - Add a 3 ⁄ 8 " flat washer to each
of (4) 3 ⁄ 8 –16 x 1 ⁄ 2 " hex bolts, then loosely attach
a 3 ⁄ 8 –16 rectangular nut. Slide one stop posi-
tioner into each end of both rails, capturing the
rectangular nut in the T-slot facing away from the
saw. Do not tighten bolt at this time.
Base clamping knob - Add a 3 ⁄ 16 " thick nylon
washer to each of (4) base clamping knobs and
loosely attach a
3 ⁄ 8 –16 dual pilot rectangular
nut. The flat side of the rectangular nut should
face the knob. Thread a
3 ⁄ 8 –16 x 3 ⁄ 8 " set screw
into the remaining hole on each rectangular nut.
Slide the base clamping knob assemblies onto
the right hand end of each rail as viewed from
the operator’s side of the table saw. Thread a
3 ⁄ 8 –16 x 3 ⁄ 8 " set screw into the remaining (4)
dual pilot rectangular nuts and slide into the left
hand end of each rail. Do not tighten set screws
or knobs at this time. See Fig. 8.
6
Left end of rail
FIG. 8
Slide stop positioner and clamping
knob assemblies onto rails
Do not tighten fasten-
ers at this time
3 ⁄ 8 " flat washer
3 ⁄ 8 – 16 x 1 ⁄ 2 " hex bolt
Base clamping knob
Right end of rail
3 ⁄ 16 " thick nylon
washer
3 ⁄ 8 – 16 x 3 ⁄ 8 " set screws
Flat side of
rectangular nut
3 ⁄ 8 – 16 rectangular nut
3 ⁄ 8 – 16 dual pilot
rectangular nuts
T-slot
Rail mounting bolt
Rail