INCRA TSIII Table Saw Fence - Manual (Page 5)

The rail positions described above will provide support
for the base of the TS III for work on either the left or
right side of the blade. Left hand range is about 16"
and right hand range is 31". These same rail positions
will accommodate the optional 18" router table on the
left or 24" router table on the right. If you wish to customize the setup to suit your needs,
just slide the rails left or right as necessary. Keep in
mind that sliding the rails to the right subtracts from
your range to the left and sliding the rails to the left
subtracts from your range to the right.
Set final mounting bracket position
Clamp the (2) TS III base clamps to the front rail as
shown in Fig. 4 and loosen the bolts that secure the
mounting brackets to your table saw. The rail and mounting
brackets will drop down until the base clamps touch the top
of your saw,
Fig. 5. This locates the final mounting bracket
position. Tighten the bolts that secure the mounting brackets
to your table saw. Repeat for the rear rail.
Mounting
bracket
FIG. 4
Set final mounting
bracket position
Base clamps
Clamp pad
Rail
Mounting
bracket
First: Clamp base clamps to
rail. Use clamp pads to avoid
marring anodized surfaces
Second: Loosen both
mounting bracket bolts.
Brackets will lower slightly
Set final rail position
Loosen the bolts that secure the rails to the mounting
brackets and slide the rails so that they extend 7" beyond
the left hand extension wing of your table saw as shown in
Fig. 6. Push the rail against the short vertical leg on the
mounting bracket and tighten the bolts that hold the rail in
place. See
Fig. 7 below.
4
5
Short vertical leg
FIG. 5
Tighten
mounting
bracket
bolts
Base clamp
Table saw
top
Mounting
bracket bolt
Mounting bracket is at
correct level when base
clamp touches table top
FIG. 6
Set final rail position
Rails should
extend 7" beyond
left hand extension
wing
FIG. 7
Tighten rail
mounting
bolts
Push rail against
short vertical leg
and tighten rail
mounting bolts
7 "
Slide stop positioner and base clamping
knob assemblies onto the rails
Base clamping knob - Add a 3 ⁄ 16 " thick nylon washer to each of (4)
base clamping knobs and loosely attach a 3 ⁄ 8 –16 dual pilot
rectangular nut. The flat side of the rectangular nut should face the
knob. Thread a
3 ⁄ 8 –16 x 3 ⁄ 8 " set screw into the remaining hole on
each rectangular nut. Slide the base clamping knob assemblies
onto the right hand end of each rail as viewed from the operator’s
side of the table saw. Do not tighten set screws or knobs at this
time. See
Fig. 8.
Stop positioner - Add a 3 ⁄ 8 " flat washer to each of (4) 3 ⁄ 8 –16 x 1 ⁄ 2 "
hex bolts, then loosely attach a 3 ⁄ 8 –16 rectangular nut. Slide one
stop positioner into each end of both rails, capturing the rectangular
nut in the T-slot as shown. Do not tighten bolts at this time.
6 FIG. 8
Assembly
Do not tighten
fasteners at this time
3 ⁄ 8 " flat
washer
3 ⁄ 8 – 16 x 1 ⁄ 2 "
hex bolt
Base clamping knob
3 ⁄ 16 " thick
nylon washer
3 ⁄ 8 – 16 x 3 ⁄ 8 " set screws
3 ⁄ 8 – 16
rectangular
nut
3 ⁄ 8 – 16 dual pilot
rectangular nuts
T-slot
INCRA TS III Owner’s Manual 5
Custom Setups
Rail mounting bolt
Rail
Left hand extension wing
Left end of rail
Right end
of rail