INCRA TSIII Table Saw Fence - Manual (Page 6)

Attach the INCRA Jig Ultra to base
support panel and loosely attach
remaining base clamp
Open the Ultra Mounting Hardware Pack. Place #10 washers
on each of the (6) #10 - 32 x
1 / 2 " phillips pan head screws. Insert
four of the screws through the slotted holes on the Ultra base
and loosely thread a #10 - 32 hex nut onto each screw. Insert
the remaining two screws through the two inside holes located in
the middle of the Ultra’s base and attach hex nuts. Slide the
hex nuts on all six screws into the T-slots on the base support
panel. The (4) screws/nuts in the slotted holes slide into the
outer T-slots. The (2) screws/nuts inside the Ultra’s base slide
into the inner T-slots. See
Fig. 12 and Detail 12A.
Center the Ultra’s base on the support panel. (Edge of Ultra
should be about 10
5 / 8 " from end of panel.) Use a square to
align the Ultra base at 90° to the panel and
tighten the screws installed in the slotted
holes only. Do not tighten the two screws
inside the Ultra’s base at this time. Slide
the hex nuts on the remaining base clamp
into the T-slots on the support panel.
4
Attach one base clamp to end of
base support panel
Open the Base Mount & Fence Glide Hardware Pack. Insert
the (8) #10-32 x
7 / 16 " phillips flat head screws in the
countersunk holes of both base clamps and loosely thread on
the #10-32 hex nuts. Slide the hex nuts on one of the base
clamps into the (4) T-slots on the base panel.
Fig. 11. Leave
about 3 / 8 " between the panel end and the vertical surface on
the base clamp as shown in Detail 11A and tighten the
screws. Set aside the
remaining fasteners from
the Base Mount & Fence
Glide Hardware Pack for
use in
Steps 2 and 3 on
page 8.
Remove
endcaps
from base
support panel
See Fig. 10 at right.
BASE MOUNT ASSEMBLY
Attach glide pads to underside of
base clamps
Peel the adhesive backing from the glide pad and adhere to the
base clamp as shown in
Fig. 9. Repeat for remaining base clamp.
1
2
FIG. 9
Adhere glide pad to
underside of base clamp
Adhesive
backed glide pad
Base clamp
FIG. 11
Attach one base
clamp to end of
base support panel
Do not tighten these two
screws at this time
Base support panel
Screws inside ULTRA base – use inner T-slots
Note: The base support panel used in the base mount
assembly is designed for use with table saws having a front
to back measurement of up to 28". If your table saw measures greater than 28" a custom cut support panel is
available. For details, e-mail us at [email protected] or
call us at the number listed at the bottom of page 12.
Endcap
FIG. 10
Base
clamp
FIG. 12
Attach ULTRA to
base support panel
10 5 ⁄ 8 "
INCRA Woodworking Tools & Precision Rules 6
#10– 32 x 7 ⁄ 16 "
phillips flat head screw
#10-32
hex nuts
Base support
panel
3
Hex nuts for screws
captured in T-slots
on support panel
Screws in slotted
holes – use outer T-slots
Detail 11A Base support panel
3 ⁄ 8 "
Base clamp
Detail 12A
Note: Do not attach glide pads until after main rail
installation has been completed. (See page 5, Figs. 4 and 5).
Base support
panel
Base clamp
Base support
panel
Machinist square
#10– 32 x 1 ⁄ 2 " phillips pan
head screws with washers