JUMO 902815 Dtrans T100 Screw-In RTD Temperature Probe Without/With Transmitter Data Sheet - Manual

2011-10-10/00477217
Data Sheet 902815 Page 1/7
JUMO GmbH & Co. KG
Delivery address: Mackenrodtstraße 14
36039 Fulda, Germany
Postal address: 36035 Fulda, Germany
Phone: +49 661 6003-0
Fax: +49 661 6003-607
E-mail: [email protected]
Internet: www.jumo.net
JUMO Instrument Co. Ltd.
JUMO House
Temple Bank, Riverway
Harlow, Essex CM20 2DY, UK
Phone: +44 1279 635533
Fax:
+44 1279 635262
E-mail: [email protected]
Internet: www.jumo.co.uk
JUMO Process Control, Inc.
8 Technology Boulevard
Canastota, NY 13032, USA
Phone: 315-697-5866
1-800-554-JUMO
Fax: 315-697-5867
E-mail: [email protected]
Internet: www.jumo.us
JUMO Dtrans T100
Screw-in RTD temperature probe
with/without transmitter
■ for temperatures from -50 to +260 °C
■ EHEDG certification
■ complies with ROHS for EU and China
■ configuration by setup program via USB interface
■ M12 × 1 plug connection; IP67 protection according to EN 60529
with machine connector plugged in
■ Product with an integrated transmitter is not intended for export to the USA!
The screw-in RTD temperature probe, which has a compact design, consists of a sheath with
an integrated temperature sensor, a process connection, and an attached housing for the
transmitter electronics. The built-in programmable 2-wire transmitter converts the resistance
value into a current signal.
The screw-in RTD temperature probe and the programmable 2-wire transmitter are used for
measuring temperatures from -50 to +150 °C (-58 to +302 °F) or to 260 °C (500 °F) with an
extension piece (without the transmitter: -50 to +200 °C or -58 to +392 °F).
The range, fine calibration or measuring circuit monitoring etc. can all be configured with the
help of a setup program.
The 4 to 20 mA or (reversed) 20 to 4 mA output signal that is provided is linear with
temperature. The instrument is designed for industrial applications and complies with the
European standards for assuring electromagnetic compatibility (EMC).
The transmitter must be protected from temperatures above 85 °C !
Technical data
Electrical connection machine connector M12 × 1, 4-pole according to IEC 60947-5-2; FIXCON-capable
Process connection G 3/8 (3/8" pipe) thread
G 1/2 (1/2" pipe) thread
G 1/2 (1/2" pipe) thread with CIP-compliant conical seal, with EHEDG certification
taper nipple with cap nut (milk pipe screw fitting)
clamping nipple according to DIN 32676
ball weld-in socket with clamping thread
weld-in socket with CIP-compliant conical seal
Varivent connections with EHEDG certification
ball weld-in socket
JUMO PEKA with EHEDG certification
Sheath stainless steel 316 L (Mat. Ref. 1.4404/1.4435);
stainless steel 316 Ti (Mat. Ref. 1.4571) (on request)
Protection type IP67 protection according to EN 60529, with the machine connector plugged in
Response time water 0.4 m/s sheath standard t
0.5
= 5 s; t
0.9
= 12 s
water 0.4 m/s sheath stepped t
0.5
= 2 s; t
0.9
= 5 s
air 3.0 m/s sheath standard t
0.5
= 40 s; t
0.9
= 110 s
air 3.0 m/s sheath stepped t
0.5
= 21 s; t
0.9
= 70 s
Measuring insert without transmitter:
Pt100 or Pt1000 temperature sensor, EN 60751, Class A, B or AA (1/3 Class B),
2- or 4-wire circuit
with programmable transmitter:
Pt1000 temperature sensor, EN 60751, Class A,
4-wire circuit