JUMO 902435 HEATtemp Push-In RTD Temperature Probe with Connecting Cable for Immersion Sleeve, Type PS/PL Data Sheet - Manual

Data sheet 902435 Page 1/8
JUMO GmbH & Co. KG
Delivery address:Mackenrodtstraße 14,
36039 Fulda, Germany
Postal address: 36035 Fulda, Germany
Phone:
+49 661 6003-0
Fax: +49 661 6003-607
E-mail: [email protected]
Internet: www.jumo.net
JUMO Instrument Co. Ltd.
JUMO House
Temple Bank, Riverway
Harlow, Essex CM20 2DY, UK
Phone: +44 1279 635533
Fax:
+44 1279 635262
E-mail: [email protected]
Internet: www.jumo.co.uk
JUMO Process Control, Inc.
8 Technology Boulevard
Canastota, NY 13032, USA
Phone:
315-697-5866
1-800-554-JUMO
Fax: 315-697-5867
E-mail: [email protected]
Internet: www.jumo.us
Push-in RTD temperature probe
for heat meter with connection cable
for immersion sleeves (type PS/PL)
 For temperatures from 0 to 180 °C
 Approval for heat meter MID and domestic approval
as exchangeable temperature probes
 Meets the requirements as per DIN EN 1434, AGFW FW202 and FW211
 Approval for cold meter and cold / heat meter combinations
 Paired and calibrated as per the German calibration regulations
 Production certified as per module D of the MID (CE and metrology sign)
 Adapted accessoried for installation (data and price sheet 902440)
Heat meter RTD temperature probes are used for temperature measurement in closed-loop
pipe systems. Thanks to the installation in thermowells with tolerance on fit for optimum thermal
coupling, the system need no longer be discharged at the time of the regular exchange once
the certification period has elapsed.
The temperature probes are approved in accordance with the EU directive 2004/22/EC (MID)
as well as according to the German calibration regulations (domestic approval). The tempera-
ture probes are available paired and calibrated. The state-approved test body for heat KF2 is
responsible for this purpose. Moreover, the production is certified according to module D of
MID, and the temperature probes are also available with the CE and metrology sign.
Note:
In Germany, temperature probes, type PS, with MID approval may no longer be installed in new
installations smaller than DN 25 pipe systems (4th. amendment of the Calibration Regulations).
Technical Data
Process connection Push-in RTD temperature probe for thermowells (immersion sleeves)
Connection Wire end ferrules
Connection cable PVC, PUR, TPE, Silicone; unshielded or shielded
For the max. connection cable lengths, refer to the table on the following page
Thermowell Type PS: stainless steel Ø 5.0 mm, Ø 5.2 mm or Ø 6.0 mm
Type PL: stainless steel Ø 6.0 mm
Thermowell with tolerance to fit for thermowells
Measuring insert Platinum temperature probe as per DIN EN 60751
Rated value: Pt100, Pt500, Pt1000; class B
Connection: 2-wire/4-wire circuit
Temperature Type PS: 0 to 150 °C
Type PL: 0 to 180 °C
Temperature difference Type PS: 3 to 150 K
Type PL: 3 to 180 K
Minimum immersion depth Type PS: > 15 mm
Type PL: 30 mm
Fitting length Type PS: 45 to 85 mm
Type PL: 85 to 450 mm
Response behavior Type PS: t
0.5
= 15 s (installed in thermowell)
Type PL: t
0.5
= 12 s (installed in thermowell)
Ambient conditions Climatic 0 to 70 °C
Protection class IP65
Electromagnetic E1
Mechanical M3
Accessories For the thermowell, refer to the data and price sheet 902440
2010-09-08/00530105