KV2 Audio SAC2 - Manual (Page 7)

+10 dB -15 dB
0
GAIN LIMITER
+15 dB -15 dB
0
LOW
+12 dB -12 dB
0
+12 dB -12 dB
0
+15 dB -15 dB
0
LOW - MID HI - MID HI
-6 dB -12 dB 0 -6 dB -12 dB 0 -6 dB -12 dB 0 -6 dB -12 dB 0
LOW-R LOW-L HI - L HI - R
0dB
+3dB
-3dB
-8dB
-13dB
X OVER
70Hz ON
120Hz
LPF
+10 dB -15 dB
0
+10 dB -15 dB
0
HI OUTPUT LOW OUTPUT
HPF
DIRECT NOTCH LEFT NOTCH RIGHT
HI PASS
40Hz
+10 dB -15 dB
0
ACTIVE
20Hz
EQ
ON
OFF
45 52
80
140
300
500
800
1.3k 1.6k Hz
300 200 450
45 52
80
140
300
500
800
1.3k 1.6k Hz
300 200 450
45 52
80
140
300
500
800
1.3k 1.6k Hz
300 200 450
45 52
80
140
300
500
800
1.3k 1.6k Hz
300 200 450
Gain
Adjusts the SAC2's input levels from -15dB to +10dB
Limiter
Adjusts the maximum output level. When this level is
exceeded, the limiter reduces the signal to the desired level
according to your setting.
The Limiter ensures that this level is not exceeded whilst
maintaining the dynamics and signal quality.
A switch by the input connector allows the user to adjust
the limiter time (fast or slow). It adjusts the attack and
decay together.
The Limiter level can be adjusted from -15dB to +10dB.
The Limiter function is indicated by Active LED.
+10 dB -15 dB
0
GAIN LIMITER
HI PASS
40Hz
+10 dB -15 dB
0
ACTIVE
20Hz
+15 dB -15 dB
0
LOW
+12 dB -12 dB
0
+12 dB -12 dB
0
+15 dB -15 dB
0
LOW - MID HI - MID HI
EQ
ON
OFF
-6 dB -12 dB 0 -6 dB -12 dB 0 -6 dB -12 dB 0 -6 dB -12 dB 0
NOTCH LEFT NOTCH RIGHT
45
52
80
140
300
500
800
1.3k
1.6k Hz
300 200 450
45
52
80
140
300
500
800
1.3k
1.6k Hz
300 200 450
45
52
80
140
300
500
800
1.3k
1.6k Hz
300 200 450
45
52
80
140
300
500
800
1.3k
1.6k Hz
300 200 450
Four-Band Equalizer
The four-band EQ section is a unique Super Analog
equalization circuit specially designed to highlight
the desired band without adversely affecting the
overall sound.
Low - Boosts or cuts Low frequencies around 20Hz by +/-15dB
Low-Mid - Boosts or cuts Low-Mid frequencies around 450Hz by +/-12dB
Hi-Mid - Boosts or cuts Low-Mid frequencies around 2.5kHz by +/-12dB
Hi - Boosts or cuts Hi frequencies around 18kHz by +/-15dB
Notch Filters
Use independent left and right notch filters to quickly and
effectively reduce room resonances and feedback issues.
Three position level switch, -6dB (left), Bypass (middle) and
-12dB (right).
The potentiometers should be used to find and tune out any
problem frequencies.
High Pass Filter
This switch selects between either a 20Hz or 40Hz high pass filter. It has a slope of 12dB/octave
and it is used to protect your subwoofer system from the frequencies that it cannot reproduce
efficiently and may cause damage.
Features
Front Panel
Page | 7