Landoll CPPS2-7 TWO-BAR PICK-UP Chisel Plow - Manual (Page 11)

1273rev701 9D990
1 6D409 Strap 1 .4
2 6D410 Spring Cap 2 1.0
3 6D362 Compression Spring, 17/64 Wire Diameter 2 1.3
4 6D361 Compression Spring, 7/16 Wire Diameter 2 4.0
5 6D406 Shank Support, Front 1 6.5
6 6D407 Shank Support, Rear 1 4.0
7 8D361 Clamp Pivot [6D408 - Clamp and Lube Fitting] 1 9.0
8 6D283 Shank - 26S, 1" x 26" Clear., Spring Cushion 1 25.6
9 6D280 Strap 1 1.2
10 6D213 Regular Chisel Point, 5/8" Thick x 2" Wide 1 4.8
11 6D215 Twisted Shovel, R.H., 3/8" Thick x 3" Wide 1 6.2
6D216 Twisted Shovel, L.H., 3/8" Thick x 3" Wide 1 6.2
12 2J097 Pin 1 1.3
13 2J600 Roll Pin, 5/16"x 1 1/2" Long 2 -
14 6D373 Machine Bolt, 5/8" x 14" Long, Gr. 5 2 1.3
15 8C065 Capscrew, 5/8" x 3" Long, Gr. 5 2 .3
16 1C210 Nut, 3/4" Regular Hex 1 -
17 1C211 Lockwasher, 3/4" Std. 1 -
18 1B166 Lockwasher, 5/8" Std. 6* -
19 1C392 Nut, 5/8" Regular Hex 6* -
20 6D303 Machine Bolt, 5/8" x 7 1/2" Long, Gr. 5 2 .7
21 6D355 Capscrew, 5/8" x 6" Long, Gr. 5 2 .6
22 5C461 Locknut, 5/8" Regular Hex 2 -
23 4K390 Plow Bolt, 7/16" x 3" Long, Gr. 5 2 -
24 7C460 Flat Washer, 7/16 Std. 2 -
25 1C314 Lockwasher, 7/16" Std. 2 -
26 1C179 Nut, 7/16" Reg. Hex 2 -
-- -- -- -- --
28 6C729 Locknut, 3/4" Reg. Hex 1 -
29 6D302 Machine Bolt, 3/4" x 7" Long, Gr. 5 1 .8
30 6D298 Plate 1 6.0
31 6D234 Shank Support 1 5.5
32 6D314 Shank - 26R, 1" x 26" Clear., Rigid
(Replaced by 6D283) 1 32.0
* Only 2 used on Rigid Mount Shank Support
TWISTED SHOVELS
If twisted shovels are to be used, it is suggested that they be arraanged on the
shanks as shown in Figure 1. L.H. means that the soil is thrown left and R.H.
means that the soil is thrown to the right. If another arrangement is desired, be
sure that the shovels have balanced positions from right side to left; i.e., a L.H.
shovel is the same distance from the center of the machine as a R.H. shovel is
o n the olpposite side. Place the plow bolts in the two bottom holes of the
shovel as shown at the left.
Page 9
Index Part No.
No. No. Description Req’d. Weight
CHISEL PLOW SHANKS & POINTS
1273rev3-20-06