Lenze MC3000 Series Drives - Manual (Page 10)

7 RG-MCMET
N2 Points
4.1 Metasys N2 Point Map
Table 3: Metasys N2 Point Map for MC3000 Series Drives
Point
Type 1
Point
#
Description (Point Name) Read (R)/
Override (R/O)
Point
Units Decimal
Places
MIN
Value
MAX
Value
Default
Value
1 1 Parameter Version R -- 0 -- -- 143 2
1 2 Software Version R -- 0 -- -- 043 2
1 3 Software Revision R -- 0 -- -- 05 2
1 4 Drive Config/Size R -- 0 0 57 --
1 5 Drive Class R -- 0 -- -- 65
1 6 Total Runtime (RUNTIME HRS) R hrs 0 0 --
1 7 Total Runtime (RUNTIME MIN) R min 0 0 --
1 8 Operational Status (RUN STATUS) R -- 0 0 10 --
1 9 Load Percent (LOAD PERCENT) R % 0 150 180 180
1 10 Motor Voltage (MOTOR VOLTS) R VAC 0
1 11 Present Fault (FAULT) R -- 0 0 23 0
1 12 Recorded Fault 1 R -- 0 0 23 0
1 13 Recorded Fault 2 R -- 0 0 23 0
1 14 Recorded Fault 3 R -- 0 0 23 0
1 15 Recorded Fault 4 R -- 0 0 23 0
1 16 Recorded Fault 5 R -- 0 0 23 0
1 17 Recorded Fault 6 R -- 0 0 23 0
1 18 Recorded Fault 7 R -- 0 0 23 0
1 19 Recorded Fault 8 R -- 0 0 23 0
1 20 PID Feedback (PID FEEDBACK) R PID 0 Note 3 Note 3 Note 3
1 21 PID Setpoint Command (PID SETPOINT) R PID 0 Note 3 Note 3 Note 3
1 22 Actual Speed (ACTUAL FREQ) R Hz 2 0 12000 --
2 01 Fault Condition (OK.FAULT) R -- 0 OK FLT OK
3 01 Command Speed (COMMAND SPD) R/O Hz 2 0 120.00 20.00
3 02 Keypad Command Speed (CMD KEY SPD) R/O Hz 2 0 120.00 20.00
3 03 Normal Acceleration (ACCEL) R/O sec 1 * 3600.0 30.0
3 04 Normal Deceleration (DECEL) R/O sec 1 * 3600.0 30.0
3 05 Local PID Command R/O PID 0 Note 3 Note 3 Note 3
3 06 Control Mode R/O -- 0
4 01 History R/O -- 0 0 (maintain) 1 (clear) 0
4 02 Start/Stop Drive (CMD RUN.STOP) R/O -- 0 0 (stop) 1 (start) 0
4 03 Speed Control Auto/Manual R/O -- 0 0 (auto) 1 (manual) 0
4 04 Clear Present Fault (CLEAR FAULT) R/O -- 0 0 1 (clear)
NOTES:
1. Point Types: 1 = Analog Input; 2 = Binary Input; 3 = Analog Output; 4 = Binary Output
2. Current Value of the parameter version, software version and software revision.
3. Units, MIN/MAX Values: for this point are defined via Drive Parameters #31, 75 and 76 respectively.
Refer to notes in sections 4.2 and 4.4.
* Refer to MC3000 Installation & Operation Manual (M301)