Rockwell Automation 800T_TC Shallow, Mini and Sealed Contact Switch Blocks - Manual

2943-99 12
1979-00 13
1000483 14
1 2
40060-226
REVISION
AUTHORIZATION
DIMENSIONS APPLY BEFORE
SURFACE TREATMENT
H
A
B
C
D
E
F
G
(DIMENSIONS IN INCHES)
TOLERANCES UNLESS
OTHERWISE SPECIFIED
REFERENCE
SHEET OF DWG.
B
DR.
CHKD.
APPD.
DAT E
DAT E
DAT E
±
N/A
±
N/A
±
N/A ANGLES:
.XXX:
.XX:
LOCATION : MILWAUKEE, WISCONSIN U.S.A.
SIZE
1 2 3 4 5 6 7 8
E-DOC
FORM NO. 979 (10/94)
G. Ushakow 7/24/02
BULLETIN 800T
SHALLOW, MINI AND SEALED
CONTACT SWITCH BLOCKS
CONTENTS FOR INSTRUCTION SHEET
M. Jutz 7/24/02
R. Malecki 7/24/02
Contact Block Mounting
(Bulletin 800T and 800TC)
Block Type
Contact Block Circuit Identification
Circuit Symbol Description
N.O. 3-4, A
N.C. 1-2, B
7-8, A
Z
5-6, B
Z
N.O. (Early Make)
N.C. (Late Break)
Identification
Cat No. Comments
Wire Range
AWG
(mm 2 )
Tight Torque
lb-in
(Nm)
Standard 800T/TC-XD1, 2, 3, 4, 1V, 2V, 3V, 4V
800T/TC–XA, XA1, 2, 4, 7, V Series A (large profile, no
longer available) Series B
& later (shallow profile)
14-18
(.5-2.5)
6-8
(.7-.9)
Mini 800T-XD5, 6 Requires special
screw provided with blocks
14-18
(.5-2.5)
6-8
(.7-.9)
MaxDuty 800T/TC-XD1M, -XD2M, -XD4M High current.
Horsepower rated.
Short Circuit Rating: 5KA, 240VAC
when protected by fuses.
10-18
(.5-6.0)
6-8
(.7-.9)
Sealed — Hi Current 800T-XAP, XD1P, XD2P 14-18
(.5-2.5)
6-8
(.7-.9)
Sealed — Medium Current 800T-XAY, XA2Y, XA4Y
800T-XD1Y, XD2Y
Requires special screw
(extended head) provided
with blocks.
14-18
(.5-2.5)
6-8
(.7-.9)
Sealed — Logic Reed 800T-XAR, XA2R, XA4R
800T-XD1R, XD2R
14-18
(.5-2.5)
6-8
(.7-.9)
PenTUFF 800T/TC-XAV, XD1V, XD2V,
XD3V, XD4V
14-18
(.5-2.5)
6-8
(.7-.9)
Self Monitoring 800TC-XD4S 14-18
(.5-2.5)
6-8
(.7-.9)
Note: For two circuit contact blocks, it is recommended that the same wire size be used for each circuit.
Sealed Switch
Contact Block
Mounting Screw Torque
5-7 lb-in
Mini Contact Block
Extender
6-8 lb-in
(.7-.9 Nm)
Octagon Ring
Operator
Standard
& Self Monitoring
Contact Block
(Shallow Contact)
Spacer
(to be used on
operators without
4 corner posts)
(.55-.8 Nm)
Level 1
Level 2
Terminal Screw Torque
THIS DRAWING IS THE PROPERTY OF
ROCKWELL INTERNATIONAL CORPORATION
OR ITS SUBSIDIARIES AND MAY NOT BE COPIED,
USED OR DISCLOSED FOR ANY PURPOSE
EXCEPT AS AUTHORIZED IN WRITING BY
ROCKWELL INTERNATIONAL CORPORATION