Rockwell Automation 931H-P2C1D-DC Active Converter, PT100/RTD User Manual
Page 2
931H-P2C1D-DC
90
88
97,8
6,1
Type
Order No.
Qty.
Plug-In Jumper
Querverbindung
Connexion transvrsale
Plug-In Jumper, 2-pole, red
1492-CJLJ6-2-R
60
Plug-In Jumper, 3-pole, red
1492-CJLJ6-3-R
60
Plug-In Jumper, 10-pole, red
1492-CJLJ6-10-R 20
Plug-In Jumper, 41-pole, red
1492-CJLJ6-41-R 10
Plug-In Jumper, 2-pole, blue
1492-CJLJ6-2-B
60
Plug-In Jumper, 3-pole, blue
1492-CJLJ6-3-B
60
Plug-In Jumper, 10-pole, blue
1492-CJLJ6-10-B
20
Markers
Verbindermarkierer
Repérage de blocs de jonction
1492-M6X10
200
Power Supply
24 V DC Output
15 W
1606-XLP15E
30 W
1606-XLP30E
50 W
1606-XLP50E
100 W
1606-XLP100E
120 W (5 A)
1606-XLE120E
Accessories / Zubehör / Accessoires
Active Converter, PT100/RTD
931H-P2C1D-DC
Installation Instructions
Beipackinformation
Notice d’utilisation
DIR 10000043420
(Version 00)
10000043420
1. General instructions
• Disconnect power prior to installation
• Installation only by Qualified personnel
• Follow all applicable local and national electrical codes
During range selection, appropriate safety
measures against electrostatic discharge (ESD)
are to be considered.
2. Application
The PT100/RTD Active Converter is designed to galvanically
isolate and convert PT100 signals into standard signals
0(4) ... 20 mA and 0 ... (5)10 V.
The output signal is calibrated switch selectable via
DIP switches (see enclosure).
3. Configuration
Set the DIP switches according to the table printed on
the enclosure (factory setting 0 ... 20 mA).
4. Mounting, electrical connection
The signal conditioners are mounted on standard TS35
rails and fixed in position by a suitable end bracket.
For terminal assignments see enclosure.
Wire cross-section max. 2.5 mm
2
.
ATEX - Approval
Rockwell Automation
UL DEMKO 09 ATEX 147279X 1201South Second Street
T
II 3G Ex nAnL IIC T4
Milwaukee, Wi 53204
U.S.A.
UL Class 1, Division 2 Markings
for selected Signal Conditioners
A.
“This equipment is suitable for use in Class I, Division 2,
Groups A, B, C and D hazardous locations or nonhazar-
dous locations only or the equivalent.”
B.
“WARNING: EXPLOSION HAZARD - Substitution of
components may impair suitability for use in Class I,
Division 2 environments.”
C.
“WARNING: EXPLOSION HAZARD - The area must be
known to be nonhazardous before servicing/replacing
the unit and before installing or removing I/O wiring.”
D.
“WARNING: EXPLOSION HAZARD - Do Not disconnect
equipment unless power has been disconnected and
the area is known to be nonhazardous.”
FOR INSTALLATION IN CLASS I, ZONE 2 LOCATIONS:
E.
This equipment is to be installed into suitable enclosure,
providing a degree of protection not less than IP 54 in
accordance with IEC 60529 unless the apparatus is
intended to be afforded an equivalent degree of protec-
tion by location.
Do not disconnect while circuit is live unless area is known
to be non hazardous. The enclosure for the installation of
the apparatus shall have a protection not less than IP54 in
accordance with IEC 60529
"This device is to be installed in area of a pollution degree
of not more than pollution degree 2, as defined in IEC
60664-1. Alternatively the device may be installed into
enclosure providing a degree of protection not less than
IP 64 in accordance with IEC 60529."
“Connectors are not to be separated when they are
energized.”
T
amb
0 °C to 55 °C
English
PT 100 2-/3-Wire as in EN 60751-1
(2-Wire-Connection by putting
bridge between 2 + 3)
according Part No.
0.8 mA
0...10V / 4...20mA / 0…5V
0...20mA (factory setting)
< 400 Ohm @ power supply ≥ 24 Vdc
> 10 kOhm
< 0.5 % of selected range
< 250 ppm/K of selected range
< 0.7 sec.
24 Vdc (±10%)
approx. 0.6 W
0...+55 °C
-25 °C...+85 °C
88 / 98 / 6.1
100 V
500 V
III
2
6. Technical data*
Input data
Input (fix)
Temperature range
Sensor current
Output data
Output
(selectable)
Load resistance
Output current
Output voltage
Accuracy
Temperature coefficent
Response time
General data
Supply voltage
Power consumption
Operating temperature
Storage temperature
Dimensions L/H/B mm
Coordination of insulation acc. to DIN EN50178, 04/98
Rated voltage
Rated surge voltage
Overvoltage category
Contamination class
* Tu 20 °C
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
10000043420_931H-P2C1D-DC.qxd:10000043420_931H-P2C1D-DC 25.01.2010 11:29 Uhr Seite 2