Metrohm 768 KF Oven - Manual (Page 24)

3.2 Remote control commands
768 KF Oven
21
│
& Root
│
Info Information
│ │
.Report Sending of formatted reports $G 3.2.2.17
│ │ │
.Select Selection of the report configuration,
│ │ │
parameters,
│ │ │
result 3.2.2.18
│ │
.Results Results of the determination
│ │ │
.PurgeTime Purge time read only 3.2.2.19
│ │ │
.CondTime Conditioning time read only 3.2.2.19
│ │ │
.SmplHeatTime Sample heating time read only 3.2.2.19
│ │ │
.LowTemp Lowest temp. during heating read only 3.2.2.19
│ │ │
.HighTemp Highest temp. during heating read only 3.2.2.19
│ │ │
.GasFlow Mean gas flow read only 3.2.2.19
│ │ │
.LowFlow Lowest flow during heating read only 3.2.2.19
│ │ │
.HighFlow Highest flow during heating read only 3.2.2.19
│ │
│ │
.ActualInfo Current information
│ │ │
.Inputs I/O lines, inputs
│ │ │ │
.Status Status of the lines read only 3.2.2.20
│ │ │ │
.Change Change in the status of the lines read only 3.2.2.20
│ │ │ │
.Clear Clears the change byte read only 3.2.2.20
│ │ │
.Outputs I/O lines, outputs
│ │ │ │
.Status Status of the lines read only 3.2.2.20
│ │ │ │
.Change Changing the status of the lines read only 3.2.2.20
│ │ │ │
.Clear Clears the change byte read only 3.2.2.20
│ │ │
.Meas Measured values
│ │ │ │
.CyclNo Cycle number read only 3.2.2.21
│ │ │ │
.SampleTemp Sample temperature read only 3.2.2.21
│ │ │ │
.OvenTemp Oven temperature read only 3.2.2.21
│ │ │ │
.GasFlow Gas flow read only 3.2.2.21
│ │ │
.Status Status of the assemblies
│ │ │ │
.BoatPos Position of the sample boat read only 3.2.2.22
│ │ │ │
.Valve Valve position read only 3.2.2.22
│ │ │ │
.Pump Pump read only 3.2.2.22
│ │ │ │
.Heating Heating power level read only 3.2.2.22
│ │ │
.Display Display
│ │ │ │
.L1 1st line 24 ASCII 3.2.2.23
│ │ │ │
.L2 2nd line 24 ASCII 3.2.2.23
│ │
│ │
.Assembly Assembly
│ │ │
.CycleTime Cycle time read only 3.2.2.24
│
│
│
Assembly Basic components of the assembly
│ │
.Prep Perform preparations $G, $S 3.2.2.25
│ │
.Heat Heating on $G 3.2.2.26
│ │ │
.Value Heating power level 0...50 3.2.2.26
│ │
.Valve Set valve position $G 3.2.2.27
│ │ │
.Pos Preselect position purge, transfer 3.2.2.27
│ │
.Boat Move sample boat $G, $S 3.2.2.28
│ │ │
.Rate Moving rate 0.1...10 3.2.2.28
│ │ │
.Pos Go to position 0...130.0 3.2.2.28
│ │ │
.SetPos Set stop points
│ │ │ │
.InPos Inner stop 0...130.0 3.2.2.28
│ │ │ │
.OutPos Outer stop 0...130.0v 3.2.2.28
│ │
.Pump Switch pump on/off $G, $S 3.2.2.29
│ │
.Outputs I/O lines, outputs
│ │ │
.SetLines Set lines $G 3.2.2.30
│ │ │ │
.L1 Line 1 active, inactive
│ │ │ │
: pulse, OFF 3.2.2.30
│ │ │ │
.L8 All lines as L1
│ │ │
.ResetLines Set all lines inactive $G 3.2.2.30