Watts WPSC16-100WPE - Manual

Sleeved WaterPEX Tubing
For Residential & Commercial Applications
ES-WP-WPSC
Job Name ––––––––––––––––––––––––––––––––––––––––––– Contractor ––––––––––––––––––––––––––––––––––––––––––––
Job Location ––––––––––––––––––––––––––––––––––––––––– Approval –––––––––––––––––––––––––––––––––––––––––––––
Engineer ––––––––––––––––––––––––––––––––––––––––––––– Contractor’s P.O. No. ––––––––––––––––––––––––––––––––––
Approval ––––––––––––––––––––––––––––––––––––––––––––– Representative ––––––––––––––––––––––––––––––––––––––––
LEAD FREE
*
Sleeved WaterPEX
®
Tubing
Sleeved WaterPEX tubing is a factory pre-assembled coil of
WaterPEX cross-linked polyethylene tubing encased in black,
SIDR 15 controlled HDPE conduit. The conduit serves as a
protective barrier for the WaterPEX tubing against abrasion for
burial and slab applications where an extra level of integrity is
required by local and/or state building codes. The conduit is not
designed to be pressurized or used for fluid conveyance. The
Sleeved WaterPEX tubing features Lead Free* construction to
comply with Lead Free* installation requirements.
Temperature-Pressure (WaterPEX)
Maximun Working Pressure:
160psi (11 bar) @ 73.4°F (23°C)
100psi (6.9 bar) @ 180°F (80°C)
80psi (5.5 bar) @ 200°F (93°C)
Specifications
System shall be plumbed using Watts Sleeved WaterPEX
cross-linked polyethylene pipe, factory sleeved using black,
SIDR15 HDPE conduit for all buried and/or slab applications.
All WaterPEX joints shall be made using Watts Lead-Free brass
CrimpRing and/or Poly-Alloy CrimpRing fittings using either the
Watts copper CrimpRing or stainless steel CinchClamp crimp-
ing methods as outlined in the Watts WaterPEX Installation
manual and guidelines.
NOTICE
Installation Guidelines
WaterPEX must be installed in accordance with all Watts Wa-
terPEX installation procedures, including information provided in
WaterPEX Installation manual and guidelines.
The HDPE conduit is not designed to be pressurized or to
convey fluid and is solely intended as a protective barrier for
the WaterPEX pipe against abrasion in buried and slab applica-
tions. When using in a buried or slab application, a minimum
of 3 inches of the conduit should protrude beyond the entry/
exit point of the burial backfill or slab. The ends of the conduit
may be sealed using electrical or duct tape to prevent ambient
debris or moisture from entering the conduit.
Approvals
• Manufactured in accordance with American Society
for Testing and Materials (ASTM International) F876
and F877 to SDR-9 dimensional standards
• Listed by the NSF International to NSF Standards 14
and 61 for use in potable water systems
• Listed by NSF International to be in compliant to the
Uniform Plumbing Code™
• Labeled B137.5 which indicates that it is compliant
to the CSA Standards B137.5
• Certified to PEX 5306 for use in continuous hot water
recirculation systems
Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts reserves the right
to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously
or subsequently sold.
MODEL NOMINAL TUBING
SIZE (WATER PEX)
CONDUIT SIZE COIL
LENGTH
PACKING
WEIGHT
I.D. O.D. I.D. Min. Wall
in. mm. in. mm. in. mm. in. mm. ft. cm. lbs. kgs.
WPSC08-100WPE 1 ⁄
2
15 5 ⁄
8
16 .824 21 .060 1.50 1.00 3048 1.2 5.4
WPSC12-100WPE 3 ⁄
4
20 7 ⁄
8
22 1.049 27 .070 1.75 1.00 3048 19.5 8.85
WPSC16-100WPE 1 25 1 1 ⁄
8
29 1.380 35 .092 2.30 1.00 3048 38.5 17.5
Dimensions – Weights
ES-WP-WPSC 1345 © 2013 Watts
USA: Tel: (978) 688-1811 • Fax: (978) 794-1848 • www.watts.com
Canada: Tel: (905) 332-4090 • Fax: (905) 332-7068 • www.watts.ca A Watts Water Technologies Company
*The wetted surface of this product contacted by consumable
water contains less than 0.25% of lead by weight.