Weller Cordless Soldering Tool - Manual

ENGLISH
INSTRUCTIONS
WARNING
Read instructions carefully and understand before
using. Use with care as this tool contains
flammable butane gas under pressure. Do not
expose to fire, flame, or temperatures in excess
of 120°F, (50°C) e.g. back shelf of car on sunny
day, etc. Hold away from body and face when
lighting. Keep out of reach of children.
SAFETY WARNING - PRESSURISED
CONTAINER
• Do not expose fuel reservoir (tank) to
temperatures in excess of 120°F, (50°C)
• Excessive gas flow, flaming, or catalyst pulsing
red, may occur when the regulator is incorrectly
adjusted (i.e. set too high). It is essential to
ignite the tool with the tip pointing away from
face and body.
• Do not use or ignite near combustible
substances.
• The cap can be replaced when hot; however,
care must be taken to avoid touching the cap
with the tip while sliding into place, otherwise
damage to the cap will certainly occur.
• Be certain that flames are completely out before
setting the tool down.
GAS TYPE
The tool operates on filtered butane gas, Weller
Cat. No. WB1 or WB2. Some gas should be visible
through the transparent section within the
temperature regulator button; gas vapor alone
will not generate sufficient pressure.
IGNITION SEQUENCE (FIG A)
The P2C is ignited by a piezo-electronic system.
The Gas On/Off switch is marked “GAS”. The
ignition switch is marked with a “lightning strike”
logo.
CAUTION: After use the tip and retaining
collar may still be hot. Allow to cool sufficiently
before touching.
Soldering, Hot Air, and Hot Knife Tips
Fit tip of choice and retaining collar. Turn
temperature regulator button to max. setting. Turn
gas on by pushing forward on switch. Click back
on piezo ignition switch, and allow the switch to
return. Glowing catalyst in the tip exhaust ports
will confirm operation.
Flame Tip
Use low to medium settings. Flame may “blow
itself out” at high gas flows. NOTE: Flame is
difficult to see in certain lighting situations.
TEMPERATURE ADJUSTMENT
Tip temperature and gas flow can be adjusted
by turning the temperature regulator button (filling
end) within the HI/LO range. It is not necessary
for the tip to glow bright red to achieve satisfactory
soldering temperatures. Experience will dictate
the temperature setting required.
GAS FILLING (FIG. B) Gas switch must
be in the OFF position before filling
Adaptors are not normally required when refilling.
To fill, hold butane refill above tool, as fuel fill is
dependent on gravity and pressure. Keep can
and tool in truly vertical position during refill. Do
not refill at an angle. Stop filling when gas spills
from valve. The special venting valve allows quick
and easy charging.
TIP REPLACEMENT (FIG. C)
Soldering, hot air, and other tips are easily
removed or installed, by unscrewing the retaining
collar and sliding the tip, collar, and nut over the
ignition assembly. Remove the tip, and replace
with new or alternate tip. Slide back into place
and screw into position. See FIG. D for tip list.
CAUTION: Hot gases of 1076°F+ (580°C+)
are emitted from the tip exhaust ports. Do not
leave the P2C unattended. If placing on
surface, leave ports facing upwards and rest
iron on the cap as per Fig. E
TIP TEMPERATURE RANGES
Soldering Tips Up to 1076°F (580° C.)
Blow Torch Up to 2372°F (1300° C.)
Hot Air Tip Up to 1150°F (625° C.)
Hot Knife Tip Up to 1076°F (580° C.)
WARNING: This product, when used for
soldering and similar applications, produces
chemicals known to the State of California to
cause cancer or birth defects or other
reproductive harm.
U.S. Department of Transportation Hazardous
Materials Regulations forbid the carriage of
butane or other flammable gas products on
passenger aircraft. Do not pack this item, or
any other flammable gas item, in any checked
or carry-on baggage.
Fig. B
Gas ON-OFF Switch
Interrupteur de gaz
« ON-OFF »
Interruptor de apagado
y encendido de gas
Ignition Switch
Interrupteur d’allumage
Interruptor de ignición
Gas Inspection Window
Fenêtre d’inspection du gaz
Ventana de inspección del gas
Temperature Regulator Button
Bouton du régulateur de température
Botón regulador de temperatura
©
Fig. A
Fig. C
Catalyst
Catalyseur
Catalizador
Retaining Nut (Threads shown cut away for clarity)
Écrou de retenue (filets montrés coupés pour plus de clarté)
Tuerca de retención (Se muestra la rosca cortada para mayor claridad)
Tip
Pointe
Punta
Tip Retention Tube
Tube de rétention de la pointe
Tubo de retención de la punta Iron Body
Corps en fer
Cuerpo de hierro
Portasol is a TrademarkTM of Oglesby & Butler Limited and is
registered ® in the following Countries: Ireland, U.S.A., France,
Benelux, Great Britain, Germany, Austria. © Oglesby & Butler
Limited 1993, Industrial Estate, Carlow, Ireland.
TEL: 353-503-43333 FAX: 353-503-43577 Oglesby & Butler Ltd. assumes no responsibility for any
errors that may appear in this document. Oglesby & Butler
Ltd. also reserve the right to alter specifications and
otherwise improve performance, at its own discretion.
Replaceable Tips
Pointes remplaçables
Puntas reemplazables
Fig. D
PPT1 PPT2 PPT3 PPT4 PPT5 PPT6 PPT7 PPT8 PPT9 PPT10 PPT11 PPT12 PPT13
1.0 S.F 2.4 S.F. 3.2 S.F. 4.8 S.F. 1.0 D.F. 2.4 D.F. 3.2 D.F. 4.8 D.F. Hot Blow Hot Knife Deflector Flame Tip Hot Blow &
Deflector
Fig. E
Self Igniting Self Igniting
Cordless Soldering Tool
Outil de brasage sans cordon
Herramienta inalámbrica para soldar
Kit Contains: Tool with soldering tip, mini blow torch tip,hot knife tip, hot air tip and
deflector, sponge and tray, storage case with tool holder, and instructions
Cette trousse contient: outils avec pointe de soudage, buse de chalumeau, pointe
à couteau chauffant, pointe à air chaud et déflecteur, éponge et plateau, boîte de
rangement avec porte-outil et directives.
Contenido del juego: Herramientas inalámbricas para soldar con punta para soldar, punta
para mini soplete de aire, punta tipo cuchillo caliente, punta para aire caliente y deflector,
esponja y base, caja de almacenamiento, soporte para la herramienta e instrucciones.