Quoizel CLE8603BN Clarke - Manual

Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax
631.231.7102
www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,
safety glasses.
Estimated Assembly Time: 20-30 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams
below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or
operate the fixture. Contact customer service for replacement parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-CLE8603BN
For Style CLE8603BN 6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc. April2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering June result.
Package Contents
A
Fixture Body
x 1
B
Lock Ball
x 2
D
Socket
Collar
x 3
C
Shade
x 3
Bulb Recommended: (3) Medium Base 100W Maximum, Alternate bulb (3) 23W CFL
F
Socket
Collar Tool
x 1
Hardware Contents
AA
Crossbar Assembly
x 1
STEP 1 Install Crossbar -
. .
A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head
of the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included)
Tighten until snug
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground Screw
AA
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red) Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
GND
R
Q U
O Z
E
L
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
Prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
STEP 3 Attach Fixture Body to
Mounting Screw
-
A. Place the Backplate of the Fixture
Body (A) over the Mounting
Screws and secure with Lock Balls
(B). Hand tighten until snug.
A
B
Mounting Screw
Backplate
Figure 3
STEP 4 Attach Shade to Fixture
Body -
A. Place Shade (C) and Steel Collar
(E) over the Socket. By using the
Socket Collar Tool (F), thread the
Socket Collar (D) onto the Socket
to secure the Shade (C). Hand
tighten until snug.
Figure 4
C
D
Socket
F
E
Steel Collar
x 3
E