Quoizel TFCS2820VB Chastain - Manual

Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax
631.231.7102
www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,
safety glasses.
Estimated Assembly Time: 30-45 minutes
Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams
below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or
operate the fixture. Contact customer service for replacement parts.
Warnings and Cautions
1of3
Assembly Instruction Sheet #IS-TFCS2820VB
For Style TFCS2820VB
Bulb Recommended: (3) Medium Base 100W Maximum, Alternate bulb (3) 23W CFL
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2013 QuoizelInc. December2013
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
A
B
C
D
F
E
Hardware Contents
Fixture Loop
x 1
Socket Assembly
x 1
Side Arms
x 3
Center Stem
x 1
Finial
x 1
Shade
x 1
AA
BB
CC
DD
EE
FF
II
Crossbar
x 1
Lock Washer
x 2
Hex Nut
x 2
Nipple
x 1
Canopy Chain Loop
x 1
Canopy Lock Ring
x 1
Ceiling Canopy
x 1
GG
Fixture Chain
x 1
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
STEP 1 Install Fixture Loop -
A. Thread the Fixture Loop (A) onto the
nipple on the top center of the Socket
Assembly (B). Hand tighten until snug.
Figure 1
A
B
STEP 2 Install Shade -
Quoizel recommends (2) people for this step.
A. Thread the short nipple end of the Center
Stem (D) into the hex coupling on the bottom
center of the Socket Assembly (B). Hand
tighten until snug.
B. Place the Shade (F) over the end of the
Center Stem (D). With one person hold the
Figure 2
F
C
D
E
B
Loop
Loop Shade (F), another person attach one
end of the Side Arm (C) to the Loop at
the Socket Assembly (B) and attach
another ends of the Side Arms (C) to
the Loops in the Shade (F).
C. Thread the Finial (E) onto the end of
the Center Stem (D). Hand tighten
until snug.
HH
Quick Link
x 2