Quoizel TFCC2822VA Classic Craftsman - Manual

OUTLET BOX
HOUSE SUPPLY and
GROUND WIRES
OUTLET BOX SCREWS
not supplied ( )
CROSSBAR
LOCK WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
LOCK WASHER B
CANOPY CHAIN LOOP
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE CHAIN
CEILING CANOPY
CANOPY LOCK RING
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE LOOP
HOOK
DECORATIVE
CHAIN
SOCKET CLUSTER
HEX COUPLING
NIPPLE with
KNURLED NUT
HANGER
SHADE
FINIAL
ASSEMBLY / INSTALLATION INSTRUCTIONS
IS-TFCC2822
2007-02-15
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
FIXTURE CANOPY
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
1 Before beginning the installation carefully unpack and
identify all parts referring to the illustration
2 Turn power to the installation point OFF at circuit breaker
3 Thread FIXTURE LOOP onto the nipple in the top center
of FIXTURE CANOPY. Hand tighten until snug.
4 Fasten the CROSSBAR to the OUTLET BOX with
(2)OUTLET BOX SCREWS(not supplied). Proceed to
thread LOCK NUT A and LOCK WASHER A onto
the top end of NIPPLE. Thread NIPPLE into the center of
CROSSBAR. Locate the LOCK NUT B onto the bottom end
of the NIPPLE. Tighten LOCK NUT A against CROSSBAR
with plier until snug.
5. Locate the FIXTURE CHAIN and determine desired
hanging height of fixture. Adjust chain by removing links if
needed. Please note that depending on chain material
thickness, you might be required to use chain pliers to
spread links open. Proceed to attach one end of chain to
FIXTURE LOOP, attached to top of fixture. Pass the
fixture wires through FIXTURE CHAIN alternating links.
Proceed to pass the fixture wires through the following
mounting components in this order: 1)CANOPY LOCK
RING; 2)CEILING CANOPY 3 CANOPY CHAIN LOOP
4 SHAKE PROOF WASHER B and LOCK NUT B
5 NIPPLE 6 LOCK NUT A and LOCK
WASHER A
6.
(2 people recommended for the remaining steps) Position
the fixture under the ceiling mounted outlet box. Pass
LOCK WASHER B over the NIPPLE. Thread
CANOPY CHAIN LOOP onto NIPPLE. Thread LOCK NUT
B down the NIPPLE, against the CANOPY CHAIN LOOP
and snug with pliers. Pass the wires through the NIPPLE.
Take up wire slack and trim wires so that approx. 6” will
remain inside outlet box. Proceed to attach the top of the
FIXTURE CHAIN to the bottom of the CANOPY CHAIN
LOOP. Using wire connectors (not supplied) connect the
HOUSE GROUND WIRE to the FIXTURE GROUND
WIRE connect the HOUSE WHITE WIRE to the
FIXTURE SUPPLY WIRE (WHITE or RIBBED SIDE);
connect the HOUSE BLACK (or RED) WIRE to the
FIXTURE SUPPLY WIRE(BLACK or SMOOTH SIDE).
Wrap each connection with approved electrical tape.
7. With the proper connections made, proceed to push the
CEILING CANOPY upward over the OUTLET BOX. Be
sure that all wires are carefully tucked into the OUTLET
BOX cavity. Secure canopy against ceiling by threading
CANOPY LOCK RING onto the CANOPY LOOP. Tighten
until snug.
11.Install bulbs referring to fixture markings and/or labels for
maximum wattage.
12 Restore power to the installation point ON. Retain this
sheet for future reference.
.
. .
.
,
, .
.
; ) ;
) ;
) ; )
.
;
.
Making the connections:
8.Locate NIPPLE with KNURLED NUT. Thread top end of
NIPPLE into HEX COUPLING underside of SOCKET
CLUSTER. Hand tighten until snug.
9.Locate close ends of DECORATIVE CHAINS onto the
HOOKS on the side of FIXTURE CANOPY. With another
person, lift SHADE upward and make the hole in the
bottom center of SHADE over end of NIPPLE. Position
the hooks on the ends of DECORATIVE CHAINS onto the
HANGERS inside of SHADE.
10.Thread FINIAL onto the end of NIPPLE and tighten until
snug to secure the SHADE.
Please note that there are
4 HANGERS and 8 HOOKS on the ends of DECORATIVE
CHAINS. The hooks need to double up on the HANGERS.