Quoizel GE5009SE Genova - Manual (Page 2)

FIXTURE SUPPLY
WIRE
SHAKE PROOF WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
SHAKE PROOF WASHER B
CANOPY CHAIN LOOP
COUPLING
FIXTURE CHAIN
CEILING
CANOPY
CANOPY LOCK
RING
FIGURE 1.
HOUSE SUPPLY
and GROUND
WIRES
HOLE DRILLED
INSIDE OUTLET
BOX
OUTLEX BOX
SET SCREWS
INSTALLATION INSTRUCTIONS:
(FOR FIXTURES OVER 25 LBS. (Canada Only)
Quoizel recommends a licensed electrician or contractor be
consulted for this installation.
3/8-18 NIPPLE, SHAKE
PROOF WASHER AND
HEX NUT (INCLUDED)
COTTER
PIN
Please use the information outlined in this sheet for the
ceiling installation part of your fixture assembly.
1. Before installing fixture, carefully unpack and identify all
parts referring to illustration FIGURE 1. Be sure the power
to the installation point is OFF
.
2.
3. With the NIPPLE properly situated, locate COUPLING and
proceed to thread onto the end of the NIPPLE protruding
into the OUTLET BOX. Thread COUPLING onto pipe until
tight. Tighten the top SET SCREW with pliers to secure
COUPLING to NIPPLE.
4. Making the connections: (Quoizel recommends (2)
people for the rest of this installation) Proceed to unravel
the FIXTURE SUPPLY and GROUND WIRES. Locate the
FIXTURE CHAIN and attach one end to the FIXTURE LOOP
at the top of FIXTURE. Please note that depending on chain
material thickness, you might be required to use chain pliers to
spread chain links open. Proceed to pass the FIXTURE
SUPPLY and GROUND WIRES through the chain, alternating
links. Proceed the pass the wires through the following
mounting components in this order: 1) CANOPY LOCK RING
2) CEILING CANOPY.
Position the fixture under the OUTLET BOX. Locate the
fixture wires through the bottom center
of the COUPLING. Pull wires through the wire way hole on side
of COUPLING.
Proceed to thread the NIPPLE into the bottom center of the
COUPLING until tight. Tighten the LOWER SET SCREW.
Proceed to thread LOCK NUT A and SHAKE PROOF
WASHER A up NIPPLE until seated against the bottom of the
COUPLING. Tighten until snug with pliers. Attach the top of the
FIXTURE CHAIN to the CANOPY CHAIN LOOP. Proceed to
attach the FIXTURE GROUND WIRE to HOUSE GROUND
WIRE using wire connector (not supplied). Using wire
connectors (not supplied), connect the HOUSE WHITE WIRE to
the FIXTURE SUPPLY WIRE (WHITE or RIBBED SIDE);
connect the HOUSE BLACK (or RED) WIRE to the FIXTURE
SUPPLY WIRE (BLACK or SMOOTH SIDE). Wrap all
connections with approved electrical tape.
5. With the proper connections made roceed to push the
CEILING CANOPY upward over the OUTLET BOX. Be sure
that all wires are carefully tucked into the OUTLET BOX cavity.
Secure canopy against ceiling by threading CANOPY LOCK
RING onto the CANOPY
LOOP. Tighten until snug.
at circuit breaker
(Refer to Figure 2, page 3) This weight of this fixture will
require a means of support independent of the OUTLET
BOX. This fixture must be supported by 3/8-18 NPSM
NIPPLE(supplied) The NIPPLE should be positioned so
that 3/4“ protrudes into the OUTLET BOX cavity. Note: the
opposite end of the NIPPLE must be attached to a
structural or bridging member of sufficient strength to
support the fixture weight. A COTTER PIN has been
included and should be installed into the top of NIPPLE,
above HEX NUT for added safety. A clearance hole must be
drilled on the inside top center of the OUTLET BOX. Please
refer to Figure 2, page 3 for detailed illustration. We
recommend the consultation of a licensed electrician or
contractor due to the complexity of this installation.
CANOPY CHAIN LOOP; SHAKE PROOF WASHER B and
LOCKNUT B; NIPPLE ; LOCK NUT A and SHAKE PROOF
WASHER A. Thread LOCK NUT A onto top end of NIPPLE.
Pass SHAKE PROOF A over top end of NIPPLE. Thread
LOCK NUT B onto the end of NIPPLE. Pass SHAKE PROOF
B over end of NIPPLE. Thread the CANOPY CHAIN LOOP
onto the end of NIPPLE. Thread LOCK NUT B down NIPPLE
and snug against top of CANOPY CHAIN LOOP with pliers.
Pass wires through the bottom center CANOPY CHAIN LOOP
through NIPPLE. Pass
Take up wire slack and trim wires so that
approx. 6” will remain inside outlet box.
p
CHAIN
6. Refer back to Page 1, Step 10 and finish installation.
IS-GE5009
Page 2 of 3
12.05
6 CORPORATE PARKWAY
GOOSE CREEK, SC. 29445
www. quoizel. com