Quoizel GY5204K Gentry - Manual

OUTLET BOX
HOUSE SUPPLY and
GROUND WIRES
OUTLET BOX SCREWS
not supplied ( )
CROSSBAR
LOCK WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
LOCK WASHER B
CANOPY CHAIN LOOP
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE CHAIN
CEILING CANOPY
CANOPY LOCK RING
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE LOOP
LOCK SCREW
UPPER COLUMN SIDE ARM
CENTER
STEM
GLASS
PANEL
LOCK
BALL
CANDLE
COVER
SOCKET
JUNCTION
BOX
SCREW
CAGE
1 Before beginning the installation carefully unpack
and identify all parts referring to the illustration
2 Turn power to the installation point OFF at circuit
breaker
3 Thread the CENTER STEM onto the coupling
on the top center of the JUNCTION BOX Hand
tighten until snug Proceed to thread the CENTER
STEM UPPER COLUMN and the FIXTURE
LOOP together Hand tighten until snug
4. Fasten the CROSSBAR to the OUTLET BOX with
(2)OUTLET BOX SCREWS(not supplied). Proceed
to thread LOCK NUT A and LOCK WASHER A onto
the top end of NIPPLE. Thread NIPPLE into the
center of CROSSBAR. Locate the LOCK NUT B onto
the bottom end of the NIPPLE. Tighten LOCK NUT A
against CROSSBAR with plier until snug.
5. Locate the FIXTURE CHAIN and determine desired
hanging height of fixture. Adjust chain by removing
links if needed. Please note that depending on chain
material thickness, you might be required to use
chain pliers to spread links open. Proceed to attach
one end of chain to FIXTURE LOOP, attached to top
of fixture. Pass the fixture wires through FIXTURE
CHAIN alternating links. Proceed to pass the fixture
wires through the following mounting components
in this order: 1)CANOPY LOCK RING; 2)CEILING
CANOPY 3 CANOPY CHAIN LOOP 4 LOCK
WASHER B and LOCK NUT B 5 NIPPLE 6 LOCK
NUT A and LOCK WASHER A
6.
(2 people recommended for the remaining steps)
Position the fixture under the ceiling mounted outlet
box. Pass LOCK WASHER B over the NIPPLE.
Thread CANOPY CHAIN LOOP onto NIPPLE. Thread
LOCK NUT B down the NIPPLE, against the CANOPY
CHAIN LOOP and snug with pliers. Pass the wires
through the NIPPLE. Take up wire slack and trim wires
so that approx. 6” will remain inside outlet box.
Proceed to attach the top of the FIXTURE CHAIN to
the bottom of the CANOPY CHAIN LOOP.
Using wire connectors (not supplied) connect the
HOUSE GROUND WIRE to the FIXTURE GROUND
WIRE connect the HOUSE WHITE WIRE to the
FIXTURE SUPPLY WIRE (WHITE or RIBBED SIDE);
connect the HOUSE BLACK (or RED) WIRE to the
FIXTURE SUPPLY WIRE(BLACK or SMOOTH SIDE).
Wrap each connection with approved electrical tape.
7. With the proper connections made, proceed to push
the CEILING CANOPY upward over the OUTLET
BOX. Be sure that all wires are carefully tucked into
the OUTLET BOX cavity. Secure canopy against
ceiling by threading CANOPY LOCK RING onto the
CANOPY LOOP. Tighten until snug.
8. Quoizel recommended 2 people for the next steps
Place the CAGE on a flat work surface Slip down
the GLASS PANELS inside of the CAGE Proceed
to position the SOCKET assembly into the center
of the CAGE and line up the mounting holes on
the side of the UPPER COLUMN with the SCREWS
on the four corners of the CAGE
9 Locate the SIDE ARMS Please make sure the
LARGE SCROLLED END is upside and the SMALL
SCROLLED END is downward Position the holes on
the bottom ends of the arms over the SCREWS on the
top end of the CAGE and match the holes on
another ends with the mounting holes on the side
of the UPPER COLUMN Secure the SIDE ARMS
with LOCK SCREWS and LOCK BALLS Hand
tighten until snug
10 Position the CANDLE COVER over the SOCKET
as shown Install the correct bulbs referring to the
fixture markings and or labels for maximum wattage
11 Restore power to the installation point ON. Retain
this sheet for future reference.
.
.
.
,
, .
.
.
.
, ,
. .
; ) ; )
; ) ; )
.
;
( )
.
.
.
. .
.
.
.
.
.
.
/ .
.
Making the connections:
ASSEMBLY / INSTALLATION INSTRUCTIONS
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
IS-GY5204
Revised 2007-11 23
-
( ) Large scrolled end
( ) Small scrolled end