Quoizel GRT5103IS Grant - Manual

Package Contents
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax
631.231.7102
www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,
safety glasses.
Bulb Recommended:
Estimated Assembly Time:
Preparation:
(3) Medium Base 100W bulbs Maximum, Alternate bulb (3) 23W CFL Maximum.
30-45 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams
below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or
operate the fixture. Contact customer service for replacement parts.
Warnings and Cautions
1of3
Assembly Instruction Sheet #IS-GRT5103
For Styles GRT IS, GRT PN and GRT5103BN 5103 5103
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc. February2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
E
B
Shade
x 3
6 ” Rod
x 2
C
12 ” Rod
x 2
D
Ring
x 3
F
Socket Collar
x 3
Socket
Assembly
x 1
G
Hardware Contents
Figure 1
Supply Wires
and Ground Wire
C
A
G
C
AA
BB
CC
DD
EE
FF
Crossbar
x 1
Lock Washer
x 2
Hex Nut
x 2
Nipple
x 1
Canopy Chain Loop
x 1
Canopy Lock Ring
x 1
Ceiling Canopy
x 1
GG
Quick Link
x 1
HH
STEP 1 Assemble the Rods and the Fixture Loop -
A. Determine the Rods (B/C) to be assembled to the Socket Assembly
(G) according to your hanging height.
B. Pass the supply wires and ground wire through the chosen rods
(B/C) and the Fixture Loop (A). Thread the Socket Assembly (G), the
chosen Rods (B/C) and the Fixture Loop (A) together. Hand tighten
until snug.
Suggested rods for Ceiling height :
8
’ ceiling : use (1)6” rod and (1)12” rod
9 ’ ceiling : use (1)6” rod and (2)12” rods
STEP 2 Install Crossbar -
A. AA) Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included)
Tighten until snug . .
Figure 2
Outlet Box
Outlet Box Screw
(not included)
Green Ground Screw
AA
A
Fixture Loop
x 1
B
B
STEP 3 Install Canopy Chain Loop and Nipple -
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25 ” from the end. Pass one Lock Washer (BB) over the end
of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).
Place another Lock Washer (BB) over the Nipple (DD) and then
thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD)