Quoizel TFKM2840VB Kami - Manual

Warnings and Cautions
1of3
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc. May2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
A
B
C
D
I
E
Hardware Contents
Fixture Loop
x 1
Socket
Assembly
x 1
Side Arms
x 8
4.73 ”L Nipple
with Hex Nut
x 1
Inner Cap
x 1
Shade
x 1
AA
BB
CC
DD
EE
FF
II
Crossbar
x 1
Lock Washer
x 2
Hex Nut
x 2
Nipple
x 1
Canopy Chain
Loop
x 1
Canopy Lock
Ring
x 1
Ceiling Canopy
x 1
GG
Fixture Chain
x 1
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
HH
Quick Link
x 2
F
G
Cap
x 1
H
Finial
x 1
2 ”L Nipple
with Hex Nut
x 1
JJ
Tuck Washer
x 1
KK
Mounting Screw
x 2
STEP 1 Install Fixture Loop -
A. Thread Fixture Loop (A) onto the nipple
on the top center of Socket Assembly (B).
Hand tighten until snug.
Figure 1
A
B
STEP 2 Install Crossbar and
Ceiling Canopy -
* Pliers is required for this step.
Drill a 5/8 ” diameter clearance hole
on the top inside center of the Oulet
Box and through the Structural
Support Member. Place Crossbar
(AA) onto Outlet Box and line up
mounting holes with a set of holes on
Crossbar (AA). Thread Outlet Box
Screws (not supplied) into the
mounting holes on the Outlet Box
and tighten until snug to secure the
Crossbar (AA). By using a
screwdriver, thread Mounting Screws
(KK) into the Structural or Bridging
Member and tighten until snug.
B. Thread one Hex Nut (CC) to one end
of the Nipple (DD) until it is at least
0.25
” from the end. Pass one Lock
Washer (BB) over the end of the
Nipple (DD) and thread the Canopy
Chain Loop (EE) onto the Nipple
(DD). By using pliers, thread the Hex
Nut (CC) against the Canopy Chain
Loop (EE) and hand tighten until
snug.
A.
Structural or
Bridging Member
Drill a 5/8 ”
Dia. Hole
Outlet Box
AA
Outlet Box
Screw (not
Supplied)
DD
BB
CC
BB
KK
EE
II
FF
Figure 2
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Bulb Recommended:
Estimated Assembly Time:
Preparation:
Medium
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
(8) Base 100W 8 bulbs Maximum, Alternate bulb ( ) 23W CFL Maximum
Assembly Instruction Sheet #IS-TFKM2840VB
For Style TFKM2840VB