Quoizel MQ5009HL Marquette - Manual

CAP
CANDLE
COVER
SOCKET
CRYSTAL
DECORATION
ARM
HANGER
LOCK SCREW
HEX
COUPLING
CENTER
COLUMN
SUPPORT
ARM
JUNCTION BOX
SCROLLED PART
SMALL TUBE
FINIAL
CRYSTAL
SPACER
TUBE
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
OUTLET BOX
HOUSE SUPPLY and
GROUND WIRES
OUTLET BOX SCREWS
not supplied ( )
CROSSBAR
LOCK WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
LOCK WASHER B
CANOPY CHAIN LOOP
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE CHAIN
CEILING CANOPY
CANOPY LOCK RING
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE LOOP
NIPPLE
ASSEMBLY / INSTALLATION INSTRUCTIONS
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
IS-MQ5009
Page 1 of 3
Revised 2008 07 07
- -
1 Before beginning the installation carefully unpack and
identify all parts referring to the illustration
2 Turn power to the installation point OFF at circuit
breaker
3 Unfold the SUPPORT ARMS to the proper locations
Position the SPACER TUBE over the HEX COUPLING
on the top end of the JUNCTION BOX assembly and
then thread the nipple on the end of the CENTER
COLUMN onto the HEX COUPLING
Hand tighten
until snug Please make sure the mounting holes on
the side of the CENTER COLUMN line up the
mounting holes on the side of the JUNCTION BOX
assembly
4 Locate the DECORATIVE ARMS Match the holes on
them with the mounting holes on the side of the
CENTER COLUMN and JUNCTION BOX assembly
Secure them by threading the LOCK SCREWS into
the mounting holes
Hand tighten until snug
5 Thread the FIXTURE LOOP onto the nipple on the top
end of the CENTER COLUMN and tighten until snug
6
Fasten the CROSSBAR to the OUTLET BOX with
(2)OUTLET BOX SCREWS(not supplied). Proceed to
thread LOCK NUT A and LOCK WASHER A onto the top
end of NIPPLE. Thread NIPPLE into the center of
CROSSBAR. Locate the LOCK NUT B onto the bottom
end of the NIPPLE. Tighten LOCK NUT A against
CROSSBAR with plier until snug.
7. Locate the FIXTURE CHAIN and determine desired
hanging height of fixture. Adjust chain by removing links
if needed. Please note that depending on chain material
thickness, you might be required to use chain pliers to
spread links open. Proceed to attach one end of chain to
FIXTURE LOOP, attached to top of fixture. Pass the
fixture wires through FIXTURE CHAIN alternating links.
Proceed to pass the fixture wires through the following
mounting components in this order: 1)CANOPY LOCK
RING; 2)CEILING CANOPY 3 CANOPY CHAIN LOOP
4 LOCK WASHER B and LOCK NUT B 5 NIPPLE
6 LOCK NUT A and LOCK WASHER A
8.
(2 people recommended for the remaining steps)
Position the fixture under the ceiling mounted outlet box.
Pass LOCK WASHER B over the NIPPLE. Thread
CANOPY CHAIN LOOP onto NIPPLE. Thread LOCK
NUT B down the NIPPLE, against the CANOPY CHAIN
LOOP and snug with pliers. Pass the wires through the
NIPPLE. Take up wire slack and trim wires so that
approx. 6” will remain inside outlet box. Proceed to
attach the top of the FIXTURE CHAIN to the bottom of
the CANOPY CHAIN LOOP.
Using wire connectors (not supplied) connect the
HOUSE GROUND WIRE to the FIXTURE GROUND
WIRE
connect the HOUSE WHITE WIRE to the
FIXTURE SUPPLY WIRE (WHITE or RIBBED SIDE);
connect the HOUSE BLACK (or RED) WIRE to the
FIXTURE SUPPLY WIRE(BLACK or SMOOTH SIDE).
Wrap each connection with approved electrical tape.
9. With the proper connections made, proceed to push the
CEILING CANOPY upward over the OUTLET BOX. Be
sure that all wires are carefully tucked into the OUTLET
BOX cavity. Secure canopy against ceiling by threading
CANOPY LOCK RING onto the CANOPY LOOP. Tighten
until snug.
10 Thread the NIPPLE into the mounting hole on the
bottom center of the JUNCTION BOX Hand tighten
until snug Proceed to locate the SCROLLED PART
SMALL TUBE over the end of the NIPPLE in turn and
secure with the FINIAL
Hand tighten until snug
11 Position the CRYSTALS onto the hangers on the
FINIAL SCROLLED PART SUPPORT ARMS and
DECORATIVE ARMS as shown
12.Position the CANDLE COVER over the SOCKET as
shown Put the CAPS onto the top end of the
CANDLE COVER Install the correct bulbs referring to
the maximum wattage affixed to the fixture.
13 Restore power to the installation point ON. Retain this
sheet for future reference.
.
.
.
.
,
, .
. .
.
.
.
. .
.
. .
.
.
( )
; ) ;
) ; ) ;
) .
;
.
.
. ,
. .
.
, ,
.
.
.
.
.
For Canadian installations please refer to Page 2
Making the connections
,
:
Please note that
there are two kinds of CRYSTALS