Quoizel MQ5208HL Marquette - Manual

OUTLET BOX
HOUSE SUPPLY and
GROUND WIRES
OUTLET BOX SCREWS
not supplied ( )
GREEN GROUND SCREW
CROSSBAR
SHAKE PROOF
WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
SHAKE PROOF
WASHER B
CANOPY CHAIN LOOP
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE CHAIN
CEILING CANOPY
CANOPY LOCK RING
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE LOOP
CENTER COLUMN LOCK SCREW
SIDE ARM
CAP
CANDLE
COVER
SOCKET
NIPPLE with
HEX NUT
HEX COUPLING
JUNCTION BOX
SCROLL PART
LOCK SCREW
CRYSTAL
SPACER TUBE
FINIAL
CRYSTAL
1 Before beginning the installation carefully unpack
and identify all parts referring to the illustration
2 Turn power to the installation point OFF at circuit
breaker
3 Locate NIPPLE with HEX NUT. Thread end of NIPPLE
into HEX COUPLING. Using pliers, thread the HEX NUT
against HEX COUPLING and hand tighten until snug.
Slip down the CENTER COLUMN and thread FIXTURE
LOOP onto the nipple to secure it. Hand tighten until snug.
4. Locate SCROLL PART and SPACER TUBE over end of
NIPPLE on the bottom center of JUNCTION BOX. Secure
them by threading FINIAL onto the NIPPLE. Hand tighten
until snug.
5. Locate SIDE ARM. Match the holes on SIDE ARM with
mounting holes on the side of CENTER COLUMN and
JUNCTION BOX. Thread LOCK SCREWS into mounting
holes to secure them. Hand tighten until snug.
6. Locate CRYSTALS onto the hangers on SCROLL PART,
FINIAL and SIDE ARMS. There are 2 kinds of CRYSTALS.
Please refer to the illustration for identification of
locations.
7 )
Fasten the CROSSBAR to the OUTLET BOX with
(2)OUTLET BOX SCREWS(not supplied). Proceed to
thread LOCK NUT A and SHAKE PROOF WASHER A
onto the top end of NIPPLE. Thread NIPPLE into the
center of CROSSBAR. Locate the LOCK NUT B onto
the bottom end of the NIPPLE. Tighten LOCK NUT A
against CROSSBAR with plier until snug.
8. Locate the FIXTURE CHAIN and determine desired
hanging height of fixture. Adjust chain by removing
links if needed. Please note that depending on chain
material thickness, you might be required to use chain
pliers to spread links open. Proceed to attach one
end of chain to FIXTURE LOOP, attached to top of
fixture. Pass the fixture wires through FIXTURE
CHAIN alternating links. Proceed to pass the fixture
wires through the following mounting components in
this order: 1)CANOPY LOCK RING; 2)CEILING
CANOPY 3 CANOPY CHAIN LOOP 4 SHAKE
PROOF WASHER B and LOCK NUT B 5 NIPPLE
6 LOCK NUT A and SHAKE PROOF WASHER A
9. (2 people recommended for
the remaining steps) Position the fixture under the
ceiling mounted outlet box. Pass SHAKE PROOF
WASHER B over the NIPPLE. Thread CANOPY
CHAIN LOOP onto NIPPLE. Thread LOCK NUT B
down the NIPPLE, against the CANOPY CHAIN LOOP
and snug with pliers. Pass the wires through the
NIPPLE. Take up wire slack and trim wires so that
approx. 6” will remain inside outlet box. Proceed to
attach the top of the FIXTURE CHAIN to the bottom of
the CANOPY CHAIN LOOP. Using wire connectors
(not supplied) connect the HOUSE GROUND WIRE to
the FIXTURE GROUND WIRE
connect the HOUSE
WHITE WIRE to the FIXTURE SUPPLY WIRE (WHITE
or RIBBED SIDE); connect the HOUSE BLACK (or
RED) WIRE to the FIXTURE SUPPLY WIRE(BLACK
or SMOOTH SIDE). Wrap each connection with
approved electrical tape.
10.With the proper connections made, proceed to push
the CEILING CANOPY upward over the OUTLET BOX.
Be sure that all wires are carefully tucked into the
OUTLET BOX cavity. Secure canopy against ceiling
by threading CANOPY LOCK RING onto the CANOPY
LOOP. Tighten until snug.
11.Position SOCKET through the CANDLE COVER and
place CAP onto the top end of CANDLE COVER. Install
bulbs referring to fixture markings and/or labels for
maximum wattage.
12. Restore power to the installation point ON. Retain this
sheet for future reference.
.
.
.
.(
,
, .
.
; ) ; )
; ) ;
) .
;
For Canadian installations, please refer to Page 2
Making the connections:
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
IS MQ5206
Page 1 of 3
2006 10-26 -
-
ASSEMBLY / INSTALLATION INSTRUCTIONS
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .