Quoizel TF1816VB Tiffany - Manual

Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Bulb Recommended:
Estimated Assembly Time:
Preparation:
(4) Medium Base 100W Maximum, Alternate bulb (4) 23W CFL
30-45 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-TF1816VB
For Style TF1816VB 6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Hardware Contents
Socket
Assembly
x 1
AA
BB
CC
DD
EE
FF
Crossbar
x 1
Lock Washer
x 2
Hex Nut
x 2
Long Nipple
x 1
Canopy
Chain Loop
x 1
Canopy Lock
Ring
x 1
Ceiling
Canopy
x 1
GG
Fixture Chain
x 1
HH
A STEP 2 Install Canopy
Chain Loop and Nipple
-
* Pliers is required for this
step.
A. Thread one Hex Nut (CC) to
one end of the Nipple (DD)
until it is at least 0.25” from
the end. Pass one Lock
Washer (BB) over the end of
the Nipple (DD) and thread
the Canopy Chain Loop (EE)
onto the Nipple (DD). By
using pliers, thread the Hex
Nut (CC) against the
Canopy Chain Loop (EE)
and hand tighten until snug.
B. Thread another Hex Nut
(CC) to the middle of the
Nipple (DD). Place another
Lock Washer (BB) over the
Nipple (DD) and then thread
June2014
AA
BB
CC
Step B
Step A
DD
CC
BB
EE
II
FF
B
Side
Chain
x 4
the Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is
about 0.375” above the Crossbar (AA).
C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop
(EE). Place the Ceiling Canopy (II) over the Canopy Chain Loop
(EE) against the ceiling to determine the correct position of the
Nipple (DD). Thread the Canopy Lock Ring onto the Canopy Chain
Loop (EE). Adjust the Nipple (DD) to allow the Ceiling Canopy (II) to
rest against the ceiling when held in place by the Canopy Lock Ring
(FF).
D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (II).
Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in
place.
Figure 2
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
E
Finial
x 1
D
Shade
x 1
Nipple with
Hex Nut
x 1
C
STEP 1 Install Crossbar -
A. AA) Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included)
Tighten until snug . .
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw AA