Quoizel DH348AN Duchess - Manual

OUTLET BOX SCREWS
not supplied ( )
LOCK WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
LOCK WASHER B
FIXTURE SUPPLY and
GROUND WIRE
FIXTURE SUPPLY and
GROUND WIRE
UNIVERSAL CROSSBAR
CEILING CANOPY
FIXTURE CHAIN
FIXTURE CANOPY
STUD
STUD
SPACER TUBE
LOCK BALL
LOCK BALL
SUPPORT ARM
SOCKET
SHADE
SOCKET COLLAR
1.Before
2.
:
(Quoizel recommends (2) people for the next 2 installations)
Using wire connectors (not supplied) connect the HOUSE GROUND WIRE to the
FIXTURE GROUND WIRE connect the HOUSE WHITE WIRE to the FIXTURE
SUPPLY WIRE (WHITE or RIBBED SIDE); connect the HOUSE BLACK (or RED)
WIRE to the FIXTURE SUPPLY WIRE (BLACK or SMOOTH SIDE). Wrap each
connection with approved electrical tape.
9
, ,
.
.
;
MAKING THE WIRING CONNECTIONS
beginning the installation carefully unpack and identify all parts referring
to the illustration.
Turn power to the installation point OFF at circuit breaker
3.Unfold the SUPPORT ARMS until lined up. Loosen the KNOB on the top end of the
FIXTURE CANOPY and remove the PLATE with the FIXTURE LOOPS. Locate the
SPACER TUBE, CHECK RING and the FIXTURE CANOPY over the COUPLING on
the top center of the JUNCTION BOX as shown. Secure them by threading the end of
STEM onto the COUPLING and tighten the HEX COUPLING against the FIXTURE
CANOPY with pliers.
4.Position the PLATE with the FIXTURE LOOPS back onto the top end of the fixture and
secure them with the KNOB. Hand tighten until snug.
5. Locate the SIDE ARMS. Match the holes on the SIDE ARMS with the STUDS on the
STEM and the SUPPORT ARMS. Secure them together by threading the LOCK
BALLS onto the STUDS. Hand tighten until snug.
6.Locate the FIXTURE CHAINS and determine the hanging height of the fixture.
Please note that depending on the chain material thickness, you might be required to
use chain pliers to spread links open. Proceed to attach the FIXTURE CHAINS onto
the FIXTURE LOOPS and the CEILING LOOPS.
7 Fasten the UNIVERSAL CROSSBAR to the OUTLET BOX with (2) OUTLET BOX
SCREWS (not supplied). Proceed to thread LOCK NUT A and LOCK WASHER A
onto the top end of the NIPPLE. Thread the NIPPLE into the center of the CROSSBAR.
Locate LOCK NUT B onto the bottom end of the NIPPLE. Tighten LOCK NUT A
against the CROSSBAR with pliers until snug.
8
. With the proper connections made, proceed to thread LOCK NUT B and LOCK
WASHER B onto the bottom of the NIPPLE. Lift the CEILING CANOPY
upward and slip the center hole over the end of the NIPPLE Be sure that all
wires are carefully tucked into the OUTLET BOX cavity Secure by threading the
KNOB onto the end of the NIPPLE and hand tighten until snug
10. Position the SHADE over the SOCKET. Secure the SHADE by threading the
SOCKET COLLAR onto the SOCKET. Hand tighten until snug.
11 Install bulbs referring to fixture markings and or labels for maximum wattage
12 Restore power to the installation point ON Retain this sheet for future reference
Please make sure the STUDS on the side of the SPACER
TUBE line up with the STUDS on the SUPPORT ARMS.
.
.
.
.
. / .
. . .
ASSEMBLY / INSTALLATION INSTRUCTIONS
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
IS DH348
2007-02-23 -
SIDE ARM
COUPLING
JUNCTION BOX
CHECK RING
STEM
HEX COUPLING
KNOB
PLATE with FIXTURE LOOPS
CEILING LOOP
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!