Quoizel PCBV1613C Platinum Collection Bravado - Manual

Package Contents
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax
631.231.7102
www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,
safety glasses.
Bulb Recommended:
Estimated Assembly Time:
Preparation:
(2) Medium Base 60W bulbs Maximum, Alternate bulb (2) 13W CFL Maximum.
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams
below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or
operate the fixture. Contact customer service for replacement parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-PCBV1613C
For Style PCBV1613C
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc. January2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
E
B
Bushing
x 3
Ring
x 1
D
Knurled Nut
x 3
H
Shade
x 1
C
Lock Screw
x 3
F
x 3
Rubber Washer
Lock Ring
x 3
G
Hardware Contents
AA
EE
Crossbar
x 1
Mounting Ball
x 1
STEP 1 Install Crossbar -
A. Attach the Lock Screw (C) from the top of the Ceiling Canopy (A).
Place the (D), the Bushing (E), the Ring (B) and the
(F) over the end of the Lock Screws (C) in turn.
Secure them together with the Lock Ring (G). Tighten until snug .
Knurled Nut
Rubber Washer
Figure 1
A
A
Ceiling
Canopy
x 1
STEP 3 Install Nipple to Crossbar -
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to the middle of the Nipple (DD). Place the
Lock Washer (BB) over the Nipple (DD) and then thread the Nipple
(DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375”
above the Crossbar (AA).
B. Position the center hole of the Ceiling Canopy (A) over the end of
the Nipple (DD). Adjust the Nipple (DD) so approx 0.375” of the
Nipple (DD) is protruding from the mounting hole on the Ceiling
Canopy (A). This adjustment may take a few tries.
C. Remove the Ceiling Canopy (A) and then tighten the Hex Nut (CC)
against the Crossbar (AA) to secure in place.
D. Thread another Hex Nut (CC) onto the end of the Nipple (DD).
Thread this Hex Nut (CC) on just enough so the inside surface of the
Ceiling Canopy (A) rests against it. * You may have to trial fit the
Ceiling Canopy (A) one more times to insure this distance also. This
I
Finial
x 3
BB
CC
DD
Lock Washer
x 1
Hex Nut
x 2
Nipple
x 1
AA
BB
CC
DD
CC
A
Step A
Step D C
D
E
B
F
G
STEP 2 Install Crossbar -
A. AA) Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug
. .
Figure 2
Outlet Box
Outlet Box Screw
(not included)
Green Ground Screw
AA
Figure 3
EE