Quoizel COR8412K Cooper - Manual

Hardware Contents
Package Contents
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax
631.231.7102
www.quoizel.com
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,
safety glasses.
Bulb Recommended:
Estimated Assembly Time:
Preparation:
Fixture can only be mounted in the direction indicated on page 2.
(1) Medium Base 150W bulb, Alternate bulb (1) 42W CFL Maximum.
30-45 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams
below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or
operate the fixture. Contact customer service for replacement parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-COR8412K
For Style COR8412K
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc. Aprial2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
A
Fixture Body
x 1
Figure 2
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
AA
BB
CC
DD
Crossbar
x 1
Lock Washer
x 1
Hex Nut
x 1
Nipple
x 1
EE
Lock Ball
x 1
STEP 1 Install Crossbar -
A. AA) Attach the Crossbar ( to the
Outlet Box with the head of the
Green Ground Screw facing you.
Secure it with Outlet Box Screws
(not included)
Tighten until snug . .
Figure 1 Outlet Box
Outlet Box Screw
(not included)
Green
Ground
Screw
AA
STEP 2 Install Nipple -
* Pliers is required for this step.
A. Thread the Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Place the Lock Washer (BB) over the Nipple
(DD) and then thread the Nipple (DD) into the Crossbar (AA) until the
Nipple (DD) is about 0.375” above the Crossbar (AA).
B. Place the backplate of the Fixture Body (A) over the Nipple (DD)
against the wall surface to determine the correct position of the
AA
BB
CC
DD
A
EE
Nipple (DD). Thread the Lock Ball (EE) onto the Nipple (DD). Adjust
the Nipple (DD) to allow the backplate of the Fixture Body (A) to rest
against the wall surface when held in place by the Lock Ball (EE).
D. Remove the Lock Ball (EE) and the Fixture Body (A). Tighten the
Hex Nut (CC) against the Crossbar (AA) to secure in place.
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red) Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
GND
2.4mm
13Ga
QUOIZEL R