Chamberlain HS670 - Manual (Page 5)

5
CLASS I – RESIDENTIAL VEHICULAR GATE OPERATOR
A vehicular gate operator (or system) intended for use in a home of one-to four single family dwellings,
or a garage or parking area associated therewith.
CLASS II – COMMERCIAL/GENERAL ACCESS VEHICULAR GATE OPERATOR
A vehicular gate operator (or system) intended for use in a commercial location or building such as a
multi-family housing unit (five or more single family units) hotel, garage, retail store or other building
servicing the general public.
CLASS III – COMMERCIAL/GENERAL ACCESS VEHICULAR GATE OPERATOR
A vehicular gate operator (or system) intended for use in a industrial location or building such as a
factory or loading dock area or other location not intended to service the general public.
CLASS IV – RESTRICTED ACCESS VEHICULAR GATE OPERATOR
A vehicular gate operator (or system) intended for use in a guarded industrial location or building such
as an airport security area or other restricted access locations not servicing the general public, in which
unauthorized access is prevented via supervision by security personnel.
SAFETY ACCESSORY SELECTION
All UL325 compliant LiftMaster gate operators will accept external
entrapment protection devices to protect people from motorized
gate systems. UL325 requires that the type of entrapment
protection correctly matches each gate application. Below are the
six types of entrapment protection recognized by UL325 for use
on this operator.
ENTRAPMENT PROTECTION TYPES
Type A: Inherent obstruction sensing system, self-contained
within the operator. This system must sense and initiate
the reverse of the gate within two seconds of contact
with a solid object.
Type B1: Connections provided for a non-contact device, such as
a photo eye can be used as a secondary protection.
Type B2: Connections provided for a contact sensor. A contact device
such as a gate edge can be used for secondary protection.
Type C: Inherent adjustable clutch or pressure relief valve.
Type D: Connections provided for a control requiring continuous
pressure to operate the operator open and close.
Type E: Built-in audio alarm (e.g., sirens, horns or buzzers).
NOTES:
UL requires that all installations must have warning signs
placed in plain view on both sides of the gate to warn
pedestrians of the dangers of motorized gate systems.
Model HS670 meets the following specifications:
UL325 ENTRAPMENT PROTECTION REQUIREMENTS
In order to complete a proper installation you must satisfy the
entrapment protection chart shown above. That means that
the installation must have one primary means of entrapment
protection and one independent secondary means of
entrapment protection. Both primary and secondary
entrapment protection methods must be designed, arranged
or configured to protect against entrapments in both the open
and close directions of gate travel.
For Example: For a slide gate system that is installed on a
single-family residence (UL325 Class I) you must provide the
following: As your primary type of entrapment protection you
must provide Type A inherent (built into the operator)
entrapment sensing and at least one of the following as your
secondary entrapment protection: Type B1- Non-contact
sensors such as photo-eyes, Type B2- Contact sensors such
as gate edges or Type D- Constant pressure control.
GATE OPERATOR ENTRAPMENT PROTECTION
Class
I & II
Class III
Class IV
A, B1, B2,
C or D
A, B1, C,
D or E
A, B1, B2,
D or E
A, B1, B2
or D
A, B1 or
B2
A, B1, B2,
D or E
A, B1, B2
or C
A, B1, B2
C or D
A or C
B1, B2
or D
A
UL325 Slide Gate Operator Swing & Gate Barrier
Installation (Arm) Operator
Class Primary
Type
Secondary
Type
Secondary
Type
Primary
Type
D or E
Moving Gate Can Cause
Injury or Death
KEEP CLEAR! Gate may move at any
time without prior warning.
Do not let children operate the gate or
play in the gate area.
This entrance is for vehicles only.
Pedestrians must use separate entrance
O P E R A T O R S P E C I F I C A T I O N S
MODEL CLASS 1 CLASS 2 CLASS 3 CLASS 4
HS670 GC
HS670 GI N/A N/A
UL325 MODEL CLASSIFICATIONS