Dell OptiPlex 755 User Manual
Page 9
The menu contains the parameters for the setup and configuration server. This menu also contains the security settings for PSK and PKI configurations.
l
Current Provisioning Mode – Displays the current provisioning TLS Mode: None, PKI, or PSK. This configuration is only shown in Enterprise Provision
Model.
l
Provisioning Record – Displays the provision PSK/PKI record data of the computer. If the data has not been entered, the MEBx displays a message
that states:
Provision Record not present
If the data is entered, the Provision Record displays the following:
¡
TLS provisioning mode – Displays the current configuration mode of the computer: None, PSK or PKI.
¡
Provisioning IP – The IP of the setup and configuration server.
¡
Date of Provision – Displays the date and time of the provisioning in the format MM/DD/YYYY at HH:MM.
¡
DNS – Displays if Secure DNS is being used or not. 0 indicates DNS is not in use, 1 indicates secure DNS is being used (PKI only).
¡
Host Initiated – Displays if the setup and configuration process was initiated by the host: 'No' indicates the setup and configuration process was
not host initiated; 'Yes' indicates the setup and configuration process was host initiated (PKI only).
¡
Hash Data – Displays the 40 character certificate hash data (PKI only).
¡
Hash Algorithm – Describes the hash type. Currently only SHA1 is supported (PKI only).
¡
IsDefault – Displays 'Yes' if the Hash algorithm is the default algorithm selected. Displays 'No' if the hash algorithm is not the default algorithm
used (PKI only).
¡
FQDN – FQDN of the provisioning server mentioned in certificate (PKI only).
¡
Serial Number – The 32 character that indicate the Certificate Authority serial numbers.
¡
Time Validity Pass – Indicates whether the certificate passed the time validity check.
l
Provisioning Server – The IP address and port number (0 – 65535) for an Intel AMT provisioning server. This configuration is only shown for the
enterprise provision model. The default port number is 9971.
l
TLS PSK – Contains the settings for TLS PSK configuration settings.
¡
Set PID and PPS – Sets the provisioning identifier (PID) and provisioning passphrase (PPS). Enter the PID and PPS in the dash format. (Ex. PID:
1234-ABCD ; PPS: 1234-ABCD-1234-ABCD-1234-ABCD-1234-ABCD) NOTE - A PPS value of ' '0000-0000-0000-0000-0000-0000-0000-0000' does
not change the setup configuration state. If this value is used the setup and configuration state stays as 'Not-started'.
¡
Delete PID and PPS – Deletes the current PID and PPS stored in ME. If there is no PID and PPS entered, the MEBX returns an error message.
Note: Using this option does NOT set the setup and configuration process parameter to "Not Started." This option sets the setup and
configuration process parameter to "In Process."
¡
Time Validity Pass – Indicates whether the certificate passed the time validity check.
l
TLS PKI – Contains the settings for the TLS PKI configuration settings.
¡
Remote Configuration Enable/Disable – Disables or enables remote configuration. If this option is not enabled, remote configuration cannot
occur.
¡
Manage Certificate Hashes – Displays the list of hashes that are currently stored and the current status. To change the active status of the
certificate press the <+> key. To delete the hash press the <del> key. To add another key press the <ins> key.
¡
Set FQDN – Sets the fully qualified domain name for the computer.
¡
Set PKI DNS suffix – Sets the PKI DNS suffix.
TLS PSK
The submenu contains the settings for TLS PSK configuration settings. Setting or deleting the PID/PPS causes a partial un-provision if the setup and
configuration is "In-process".
l
Set PID and PPS – Sets the PID and PPS. Enter the PID and PPS in the dash format. (Ex. PID: 1234-ABCD ; PPS: 1234-ABCD-1234-ABCD-1234-ABCD-
1234-ABCD) Note - A PPS value of '0000-0000-0000-0000-0000-0000-0000-0000' does not change the setup configuration state. If this value is used
the setup and configuration state stays as "Not-started."
l
Delete PID and PPS – Deletes the current PID and PPS stored in ME. If there is no PID and PPS entered, the MEBX returns an error message.