Document Outline

• FM Stereo FM-AM Receiver
  • WARNING
    • To prevent fire or shock hazard, do not expose the unit to rain or moisture.
      • IMPORTANT
      • CAUTION
      • Note to CATV system installer
      • Owner's record
      • For the customers in Canada CAUTION
  • Precautions
    • On safety
    • On power sources
    • On placement
    • On operation
    • On cleaning
    • For the customers in the USA
  • About This Manual
    • Type of differences
    • Getting Started
    • Receiver Operations
      • Conventions
    • Additional Information
    • Index 25
    • Rear Panel Descriptions 26
    • Remote Button Descriptions 27
    • Quick Reference Guide (back cover)
  • Hookup Overview
    • Inserting batteries into the remote
      • Notes
    • Before you get started
  • Antenna Hookups
    • FM outdoor antenna
    • Overview
    • Hookups
      • AM loop antenna
      • Q If you have poor AM reception
    • Connecting a ground wire
  • Audio Component Hookups
    • Overview
      • What cords will I need?
    • Hookups
      • Turntable
      • Tape deck
      • DAT/MD
  • Speaker System Hookups
    • Overview
      • (+)
      • (+)
    • Hookups
      • Front speakers Front speaker (R)
      • Active woofer
      • 'Q' If you have an additional front speaker system
      • 'Q' If your TV monitor uses separate speakers
    • Selecting the impedance (STR-D965 only)
    • Selecting the speaker system
  • TVAfCR Hookups
    • Overview
    • Hookups
      • TV
      • MONITOR
  • AC Hookups
    • Connecting the AC power cord
  • Selecting a Component
    • Watching video programs
    • Using the remote | § [
      • To turn off the components
      • y' If you use a Sony TV
  • Receiving Broadcasts
    • To receive other stations
    • If the STEREO indicator remains off
    • 'Q' If an FM stereo program is distorted
    • 'Q' If you cannot tune in a station and the entered numbers are flashing
    • 'Q' To watch FM simulcast TV programs
    • y If you enter a frequency not covered by the tuning interval
  • Presetting Radio Stations
    • Receiving broadcasts by scanning stations (automatic tuning)
      • If "MEMORY" goes out before you specify the preset number, start again from step 3.
      • To change a preset station
      • 'Q' If scanning stops too frequently (for FM band only)
      • Note
    • Tuning preset stations (preset tuning)
      • 'Q'You can tune by scanning the preset stations
  • Indexing
    • Indexing preset stations
      • You can check the frequency of the indexed station
    • Scanning indexed stations (index tuning)
      • To select different station indexes
    • Indexing program sources
      • If you've made a mistake
  • Recording
    • Recording on an audio tape or MiniDisc
      • 'Q' You can monitor the sound being recorded
      • Note
    • Recording on a video tape
  • Using the Sleep Timer [j
    • 'Q' You can replace audio while copying a video tape or laser disc
    • 'Q' You can freely specify the time
    • 'Q' You can check the time remaining before the receiver turns off
  • Using Pre-programmed Sound Fields
    • To turn off the sound fields
    • You can find Dolby Surround-encoded software by looking at the packaging
    • Note
  • Taking Advantage of the Sound Fields
    • How can you customize the sound fields?
    • Before you get started
  • Customizing Sound Fields
    • Adjusting the tone parameter
    • Adjusting surround sound parameters
      • Note
    • Resetting customized sound fields to the factory settings
  • Getting the Most Out of Dolby Pro Logic Surround Sound
    • Selecting the center mode
    • Adjusting the speaker volume j
      • You can adjust all speakers at one time
      • You can increase the output level of the rear speakers
    • Adjusting the delay time
    • Adjusting the tone
  • Operating One Component While Using Another (background operation)
  • Changing the Factory Setting of a FUNQION Button
    • To reset the setting to the factory setting
  • Programming the Remote (for STR-D%5 only)
    • 'Q' When you program the recording signal
    • *Q' If you cannot successfully program signals, check the following:
    • Notes
    • Clearing the programmed signal
      • If the LEARN indicator flashes rapidly
  • Troubleshooting
    • There's no sound or only a very low-level sound is heard.
    • The left and right sounds are unbalanced or reversed.
    • Severe hum or noise is heard.
    • No sound is heard from the center speaker.
    • No sound or only a very low-level sound is heard from the
    • Radio stations cannot be tuned in.
    • Surround effect cannot be obtained.
    • No picture or an unclear picture is seen on the TV screen.
    • Recording cannot be made.
    • The remote does not function.
  • Specifications
    • Audio power specifications
  • Glossary
    • A.B
    • E,F,G
    • H
    • I, J,K
    • M
    • N, O
    • w, X, Y, Z
    • Names of controls
    • Buttons
    • Switch and selector
    • Controls
    • Jacks
    • Indicators
    • Other
  • Remote Button Descriptions
  • Receiving Broadcasts Receiving Preset
    • (direct tuning) Stations
    • Example: Receiving FM 102.50 Example: Receiving the station Example: Watching a Dolby MHz number A7 Surround-encoded movie on
    • laser disc
      • ♦
  • Scanning Radio Selecting a
    • Stations (automatic tuning) Component
    • Example: Scanning FM stations
    • Example 1: Playing a CD
      • ♦
    • Example 2: Watching a video tape
      • ♦
  • Scanning Preset Stations
    • Example: Scanning stations indexed as "JAZZ"