Environmental Water Systems CWL CHLORAMINE 1865 - Manual (Page 5)

5
Assembly Instructions - Chloramine Spectrum Systems Only
CHECKING THE PARTS LIST PRIOR TO ASSEMBLY
Below is a box count for each system and its’ contents.
EWS-CC-1465-7 and CWL-CC-1465-7 should have 6 boxes.
 One Box - Tall containing the 14” x 65” Tank with a 1.05” (26.67mm) Riser ( ICN Riser Manifold - EWS Series only)
 One Box (master carton) contains Valve, Valve Screen, Bypass Valve, Adaptors, Riser Cap, Funnel, Service Information Packet
 One Box contains 50 lbs. underbed (pea gravel material specific to this system, filtration media and flow rate)
 Three Boxes containing 1 cubic foot each of EWS’ proprietary Chloramine Reduction Media (CRM)
EWS-CC-1865-7 and CWL-CC-1865-7 should have 8 boxes.
 One Box - Tall containing the 18” x 65” Tank with a 1.26” (32mm) Riser (ICN Riser Manifold - EWS Series only)
 One Box (master carton) contains Valve, Valve Screen, Bypass Valve, Adaptors, Riser Cap, Funnel, Service Information Packet
 One Box contains 50 lbs. underbed (pea gravel material specific to this system, filtration media and flow rate)
 Five Boxes containing 1 cubic foot each of EWS’ proprietary Chloramine Reduction Media (CRM)
ASSEMBLY PROCEDURE - ALL SPECTRUM CHLORAMINE SYSTEMS
1. From tall box remove Tank.
Caution: Riser (or ICN Riser Manifold - EWS Series only) is in the Tank. Do not remove and be careful not
to damage. Riser will be positioned upon the loading of the underbed and filtration media.
2. Move the Tank to (or near) the systems’ final install location. The Tank will be getting heavy once filled.
3. From master carton remove Valve, Valve Screen, Bypass Valve, Adaptors, Riser Cap and Funnel.
4. Cap the top of the clean Riser to prevent filling with CRM filtration media. Use Riser Cap included or any heavy-duty tape.
5. Place or adjust capped Riser in the center of the tank.
Caution: Riser rests at the bottom and center of Tank. Do not press down and follow loading instructions.
6. Load the Tank, using supplied Funnel in the following order:
A: From one box with Underbed (a “pea gravel” for better water distribution) load all materials until box is empty.
Caution: Slowly fill and make small adjustments as needed to make sure Riser is straight up and down, and
centered in Tank.
B: Find 3 (1465 systems) or 5 (1865 systems) boxes with pre-measured CRM filtration media. This material is black and
granular. Empty all the contents of each box into the Tank.
Note: Top 1/3 of Tank should be empty. This is called freeboard for proper backwashing of the system.
Caution: Slowly fill and make small adjustments as needed to make sure Riser is straight up and down, and
centered in Tank.
Caution: Media is dusty. Do not inhale. Work in area with good ventilation and/or take preventative measures.
7. After Underbed and all CRM filtration media is loaded, remove the Riser Cap or tape from the top of the Riser.
8. Installation of the Valve onto the Tank:
A: Connect Valve Screen to the bottom of the Valve before connecting Valve to the Tank
B: Make sure the top of the Tank and Tank threads are clean of any debris or materials from Steps 1 through 6.
C: Center Riser where the Riser fits up into the center & bottom of the Valve. The Valve Screen at the bottom of the Valve
will help center and guide the Riser into the proper position. Back off the installation if resistence occurs and retry unitil
Riser fits into position without any issues.
Warning: DO NOT force Riser up into the center & bottom of the Valve. Riser should be straight and centered and
should fit snugly into that position. A Riser that is forced to fit, bent or off-center may fail under pressure.
D: Install the Valve onto the Tank by turning clockwise. Be careful not to cross-thread Valve onto Tank.
9. Thank you for properly filling and assembling the Tank, all its’ contents and connecting the Valve.
Please go to Page 7 and follow all instructions for the proper setup, installation and startup of all Spectrum Systems.