La-Z-Boy SlumberAir Mattress System - Manual (Page 3)

5 4
– To reduce the risk of electric shock, serious injury or death:
• Disconnect the electrical plug from the wall outlet before cleaning, moving, servicing or when not
in use for an extended period of time.
• Do not use this product if it is wet, in water, around water or any liquid. Do not handle the plug or
remote control with wet hands.
• Do not sit or lie on mattress except when it is fully extended. Never close unit with person or animal inside.
• To prevent suffocation keep plastic bags away from children.
– To reduce the risk of burns, fire, electric shock,
serious injury or death:
• Always keep open flame and lit cigarettes away from upholstered furniture. Upholstered furniture
may burn rapidly with toxic gas and thick smoke.
• Closely supervise children and disabled persons using this product.
• This product has many moving parts, serious injury can occur if not used properly. Keep hands,
fingers and body parts away from the mechanism. To reduce the risk of head entrapment and other
injuries, keep children and pets away from openings and moving parts in and around furniture.
• Do not stand, sit, or place extra weight on the arms, or back.
• Do not use this product if it is damaged. Do not use attachments or substitute parts.
• This product is intended for indoor residential use only.
• Check the condition of the power transformers, electrical cords, plugs, and connectors monthly.
Keep the power transformers and electrical cords away from heat sources. Never operate the unit
with a damaged power transformer, electrical cord, plug, or connector. Contact your La-Z-Boy
®
dealer for service.
• This product is not intended for use as a health care device.
• Do not use this product where aerosol (spray) products are being used or where oxygen is being administered.
• Use care when moving the product. Before lifting the product, secure the mechanism to prevent
unexpected opening or movement. Never move the product by the mechanism, legrest, handle,
reclining back, or swivel base. Disconnect modular units. Securely grip non-moving parts only.
• Do not sit or place extra weight on the head area of the sleep sofa mattress. Excess weight can
cause the sleep surface to tip up and back.
• Do not attempt to disassemble or service the pump or motor; no serviceable parts are inside.
Contact your La-Z-Boy ® dealer for service.
• Do not allow electrical cord to be pinched between moving parts or between the frame and the
floor. Do not place cord under carpet or in location where it could become worn.
• To reduce the risk of electric shock, this product has a polarized plug (one blade is wider than the
other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do
not change the plug in any way.
• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power
plug and pull it out.
• If you give this product to someone else, include this Operating Instructions manual.
Important Safety Instructions:
Important: Read these instructions thoroughly before using.
DANGER
WARNING
Save These Instructions
F IGURE 3 F IGURE 1 F IGURE 2
SlumberAir ™ Mattress System Setup Instructions
– To reduce the risk of injury:
• Do not sit or place extra weight on the head area of the sleep sofa mattress. Excess
weight can cause the sleep surface to tip up and back.
WARNING
SETTING UP YOUR SLEEP SOFA WITH SLUMBERAIR ™ MATTRESS:
IMPORTANT:
Do not place water, or other liquids, inside the air cushion mattress. The air cushion mattress is
intended for air only. Do not place sharp, or hot objects on top of, or near, the mattress, which could
penetrate the quilting and damage the air cushion mattress.
1. Remove all loose cushions. Grasp the handle located in the center of the deck and lift in an upward
direction, and then out (F IGURE 1).
2. Step backward and pull the sleeper mechanism out to the first extended position. When it
reaches this position, the center support legs of the mechanism will rest on the floor (F IGURE 2).
3. Reach over and grasp the center of the one-piece front leg. Pull up and lower the front leg
to the floor (F IGURE 3).