Petsafe Big Dog Remote Trainer - Manual (Page 6)

10 US Customer Care Center 1-800-732-2677 www.petsafe.net 11
Transmitter Digital Display
The display stays on for approximately 30 seconds after a button press. After 30 seconds with no
button press, the display shuts off and the Transmitter goes into battery conservation mode. Pressing
any button will turn the display back on. The symbols on the display are explained below.
L indicates low stimulation levels ranging from 1-8, and appears in the lower left
corner before the battery indicator.
H indicates high stimulation levels ranging from 1-8, and appears in the lower
right corner after the battery indicator.
The battery indicator provides constant awareness of your battery’s power level.
Divided into segments, 3 indicates high battery power, 2 indicates medium, 1
indicates low (replace soon) and no bars indicate critically low (replace immediately).
Note: Red LED will flash 3 times every 5 seconds to indicate low battery.
Indicates Transmitter is ready to pair with Receiver Collar. Press Stim Down (-)
button through the stimulation levels to display and begin pairing.
Transmitter LED Indicator Light – Function and Response
Button Button Function Transmitter Indicator Light Response
Tone (green) Delivers audible tone to collar Green LED on for length of button press
Stimulation
(yellow)
Delivers stimulation to collar based on
current level shown on Digital Display
(stimulation will time-out if pressed
continuously for 12 seconds or longer
and will reset after release)
Red LED on for length of button press
Note: Red LED will also flash 3 times
every 5 seconds to indicate low battery.
+2 Boost (red) Delivers stimulation at 2 levels higher
than the current setting (can not exceed
level 8 High and will also time-out after
button is held for 12 continuous seconds)
Red LED on for length of button press
Tone and
Stimulation
Buttons held
simultaneously
Transmits Pairing command to
Receiver Collar when P is visible on
Digital Display
Orange LED on for length of button press
Prepare the Receiver Collar
To Insert and Remove the Batteries
1. Remove the screws with a small
Phillips screwdriver, applying
adequate pressure for the
screwdriver head to fit snugly
into the screw ( 2A).
2. Push the Battery Lid up
according to the arrows
stamped on the Battery Lid ( 2A).
3. Slide the Battery Lid out.
4. Install two (2), 3-volt batteries
positive (+) side up ( 2B).
Slide the Battery Lid into the
Receiver Collar.
5. Reinstall the screws ( 2B). Do not
over-tighten the screws.
TO REMOVE
SLIDE THEN LIFT
TO REMOVE
SLIDE THEN LIFT
Batteries
(CR2032)
2A
2B
Replacement batteries (3-volt, CR2032) can be found at many retailers. Contact the Customer Care
Center or visit our website at www.petsafe.net for a list of common retailers.
Risk of explosion if battery is replaced by an incorrect type. Do not short circuit, mix
old and new batteries, dispose of in fire, or expose to water. When batteries are stored
or disposed, they must be protected from shorting. Dispose of used batteries properly.
To turn Receiver Collar On
1. Press and hold the On/Off Button until the unit beeps and the Green LED light comes on.
(This takes approximately one second.)
2. Release the On/Off Button.
In normal mode, the Green LED will flash once every 5 seconds, indicating the Receiver
Collar is on and ready to receive a signal from the Handheld Transmitter.
To turn Receiver Collar Off
1. Press and hold the On/Off Button until the unit beeps and the LED light shuts off. (This takes
approximately 3 seconds.)
2. Release the On/Off Button. Note: To extend the life of the batteries, turn the Receiver Collar
off when it is not in use.
Important: If the Receiver Collar is left on continuously, the maximum battery life will be
two weeks.
Step 2