Panasonic CF-M32 Series User Manual
Operating instructions cf-m32 series, Personal computer
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Advertising
Personal Computer
OPERATING INSTRUCTIONS
CF-M32 Series
Contents
Getting Started
Read Me First ......................... 4
Names of Parts........................ 8
^ First-time Operation.......... ........ 11
Operation
Creating Backup OisKs....... 21
Compubr>g On The Road.... 24
Usmg the Battery Pack____ 30
Security Measures................ 36
Infrared Data Communications.40
Add-ons/Peripherals.............42
Troubleshooting
List of Error Codes............... 52
Dealir>g With Problems....... 53
Remstal«>g Software...»...... 56
Appendix
UUTTEO USE LICENSE AGREEMENT . . ee
WMows 95 Setup Procedure_70
Creeang a H*errwbon Data Arae 71
Setup Uteiy..... ..................... 73
Key Combinations................ 80
LED Indicators ..................... 82
Specif)catior)s ...................... 83
Advertising
Table of contents
Document Outline
- Customer's Record
- Introduction
- Illustrations in this Manual
- Copyright
- Disclaimer
- Trademarks
- Federal Communications Commission Radio Frequency Interference Statement
- Lithium Battery!
- Read Me First
- Names of Parts
- starting Up/Shutting Down
- Creating Backup Disks
- Computing On The Road
- Four Important Points
- Conserving Power
- Things to Remember
- ( Leave your computer off when it is not in use (cépage 18) P Adjust the brightness (dark) with(^+(F2| (cépage so)
- > Before stepping away from your computer, press ^n\+ [FIO] to put your computer in the standby mode(a=page 81)
- In the power management mode, the setting of [Power Saving] is recommended (cépage 26)
- Enter the following settings under [Operation Setting] in [Panasonic Power Management] (cépage 26)
- NOTE>
- Computing On The Road
- Computing On The Road
- Using the Battery Pack
- Precautions
- Using the Battery Pack
- Using the Battery Pack
- Accurately Displaying Battery Capacity
- 1 Attach the battery pack, then connect the AC adapter
- 2 Once the battery indicator turns green, remove the AC adapter (full charge)
- 3 Use the discharge tool to fuiiy discharge the battery pack.
- ^ Connect the AC adapter and charge the battery pack until the battery indicator turns green (full charge)
- When you do not want your computer to be used without permission
- When the user password is set
- 1 Run the Setup Utility (c^ page 73)
- 2 Using Q and QJ , select [System Setup] then press
- [Enter]
- 3 Using Q and Q , select [User Password], then press [Enterl
- ^ # To enable or change your password
- #To disable your password
- 5 At the confirmation screen, press ¡Enter)
- S Press [escI to end the password setting procedure 7 Close the Setup Utility (q* page 74)
- Accurately Displaying Battery Capacity
- Security Measures
- When you do not want your Supervisor Setup changed without permission
- I When the supervisor password is set in the setup utility (o-page 78),
- Setting the supervisor password (enabling, changing, disabling) 7 Run the Setup Utility (q> page 73)
- 2 Using Q and 0 , select [Supervisor Setup] then press
- [Enter]
- 3 Using Q and Q , select [Supervisor Password], then press (Enter]
- ^ # To enable or change your supervisor password
- #To disable your password
- 5 At the confirmation screen, press [Enter]
- 6 Press [Esc] to end the password setting procedure
- 7 Close the Setup Utility (c5= page 74)
- When you do not want your Supervisor Setup changed without permission
- Infrared Data Communications
- Add-ons/Peripherals
- Connecting/Disconnecting the Port Replicator
- ctWQ
- Port Replicator Attachment Diagram
- Using the External Floppy Disk Drive (FDD)
- Connecting/Disconnecting the External FDD
- Using PC Cards
- Installing/Removing the PC Card
- Adding Memory
- Installing/Removing the RAM Module 1 Power off your computer (o-page 18)
- 2 Disconnect your computer from the power outlet
- 3 Remove the battery pack (cépage 32)
- 4 Turn your computer over and use a screwdriver to remove the screw shown in the illustration
- 5 Open the display and remove the memory cover
- 6 9 Installing the RAM module
- 1 Removing the RAM module
- 7 Put the cover back into place, then close the display
- 8 Turn your computer over and use a screwdriver to fasten the screw
- Using an External Display
- 1 Power off your computer (a=page 18)
- 2 Connect the external display to your computer
- 3Turn on the display, then turn on your computer with the LCD panel opened
- 1 Run the Setup Utility (opage 73).
- 2 Using(i|andfî), select [System Setup], then press
- 3 Using QandQ, select [Video Setup], then press
- [Enterl
- 4 UsingfnandQ, select [Display], select the display with ¡then press[Esc]
- 5 Close the Setup Utility (cépage 74).
- 4Select your external display
- Using a Printer
- List of Error Codes
- Dealing With Problems
- Reinstalling Software
- LIMITED USE LICENSE AGREEMENT
- Setup Utility
- Key Combinations
- LED Indicators
- Index