Cypress CY7C1312BV18 User Manual

Mbit qdr™-ii sram 2-word burst architecture, Features, Configurations

Advertising
background image

18-Mbit QDR™-II SRAM 2-Word

Burst Architecture

CY7C1310BV18, CY7C1910BV18
CY7C1312BV18, CY7C1314BV18

Cypress Semiconductor Corporation

•

198 Champion Court

•

San Jose

,

CA 95134-1709

•

408-943-2600

Document #: 38-05619 Rev. *F

Revised June 2, 2008

Features

■

Separate independent read and write data ports

❐

Supports concurrent transactions

■

250 MHz clock for high bandwidth

■

2-word burst on all accesses

■

Double Data Rate (DDR) interfaces on both read and write ports
(data transferred at 500 MHz) at 250 MHz

■

Two input clocks (K and K) for precise DDR timing

❐

SRAM uses rising edges only

■

Two input clocks for output data (C and C) to minimize clock
skew and flight time mismatches

■

Echo clocks (CQ and CQ) simplify data capture in high-speed
systems

■

Single multiplexed address input bus latches address inputs
for both read and write ports

■

Separate port selects for depth expansion

■

Synchronous internally self-timed writes

■

Available in x8, x9, x18, and x36 configurations

■

Full data coherency, providing most current data

■

Core V

DD

= 1.8V (±0.1V); IO V

DDQ

= 1.4V to V

DD

■

Available in 165-Ball FBGA package (13 x 15 x 1.4 mm)

■

Offered in both Pb-free and non Pb-free packages

■

Variable drive HSTL output buffers

■

JTAG 1149.1 compatible test access port

■

Delay Lock Loop (DLL) for accurate data placement

Configurations

CY7C1310BV18 – 2M x 8

CY7C1910BV18 – 2M x 9

CY7C1312BV18 – 1M x 18

CY7C1314BV18 – 512K x 36

Functional Description

The CY7C1310BV18, CY7C1910BV18, CY7C1312BV18, and
CY7C1314BV18 are 1.8V Synchronous Pipelined SRAMs,
equipped with QDR™-II architecture. QDR-II architecture
consists of two separate ports: the read port and the write port to
access the memory array. The read port has data outputs to
support read operations and the write port has data inputs to
support write operations. QDR-II architecture has separate data
inputs and data outputs to completely eliminate the need to
“turn-around” the data bus required with common IO devices.
Access to each port is accomplished through a common address
bus. The read address is latched on the rising edge of the K clock
and the write address is latched on the rising edge of the K clock.
Accesses to the QDR-II read and write ports are completely
independent of one another. To maximize data throughput, both
read and write ports are provided with DDR interfaces. Each
address location is associated with two 8-bit words
(CY7C1310BV18), 9-bit words (CY7C1910BV18), 18-bit words
(CY7C1312BV18), or 36-bit words (CY7C1314BV18) that burst
sequentially into or out of the device. Because data can be trans-
ferred into and out of the device on every rising edge of both input
clocks (K and K and C and C), memory bandwidth is maximized
while simplifying system design by eliminating bus
“turn-arounds”.

Depth expansion is accomplished with port selects, which
enables each port to operate independently.

All synchronous inputs pass through input registers controlled by
the K or K input clocks. All data outputs pass through output
registers controlled by the C or C (or K or K in a single clock
domain) input clocks. Writes are conducted with on-chip
synchronous self-timed write circuitry.

Selection Guide

Description

250 MHz

200 MHz

167 MHz

Unit

Maximum Operating Frequency

250

200

167

MHz

Maximum Operating Current

x8

735

630

550

mA

x9

735

630

550

x18

800

675

600

x36

900

750

650

[+] Feedback

Advertising
This manual is related to the following products:
Table of contents