Document Outline

• Weight Processor
• HI 6300 Series
• User’s Guide
• Contents
  • Chapter 1
  • Overview 1
    • Chapter 2
  • Specifications 5
    • Chapter 3
  • HI 6300 Installation 7
    • Chapter 4
  • Network Configuration 25
    • Chapter 5
  • Instrument Configuration 39
    • Chapter 6
  • Calibration 85
    • Chapter 7
  • Operation 95
    • Chapter 8
  • Security 105
  • Chapter 9 Troubleshooting 115
  • Chapter 1
• Overview
  • General Introduction to the HI 6300 Series Weight Processor
  • HI 6300 Series Weight Processor Description
    • Typical Applications
  • Features and Capabilities
    • Hardy Process Toolbox
    • C2® and eCal™ Calibration
    • WAVERSAVER®
    • INTEGRATED TECHNICIAN®
    • Weighing System Tests
  • Chapter 2
• Specifications
  • Basic Specifications
    • General
      • Number of Channels
      • Update Rate
      • Resolution
      • WAVERSAVER
      • Averages
      • Input
      • Non-linearity
      • Common Mode Rejection
      • Common Mode Voltage Range
      • Front Panel (optional)
      • Load Cell Excitation
      • C2 Calibration Input
      • Cable Lengths
    • Network Connectivity
    • Environmental Requirements
      • Operating Temperature Range
      • Temperature Coefficient
      • Storage Temperature Range
      • -40 to 85º C (-40º to 185º F)
      • Humidity Range
      • Maximum Altitude for Installation
    • Pending Approvals
    • Remote Display Mount
    • Blind Unit (No display)
    • Disassembly and Reassembly Notes and Cautions
  • Load Cell Wiring Diagrams
    • Connecting to the Hardy HI 215IT or HI 6010/6020IT Summing Box
  • Chapter 3
• HI 6300 Installation
  • Unpacking
  • Spare Parts List
  • Tool List
  • Installing the HI 6300 Series Instrument
    • Installation options for the HI 6300 series instrument
      • Mounting the Front Panel Display
    • Panel Mount Option 1
    • Panel Mount Option 2
    • Making Longer Display Interface Cables
    • DIN Rail Mount
    • Wall Mount
  • Chapter 4
• Network Configuration
  • Ethernet TCP/IP Network Configuration
  • LAN Connection
    • If the DHCP service fails, the instrument will default to the Fixed IP address after a power cycle. If the DHCP service is repaired, the instrument will revert back to using the DHCP IP address.
    • DHCP Configuration Using the Front Panel
    • Direct Connect Hardware
    • Windows PC Configuration
    • Windows 2000
    • Windows XP
    • Windows 7
    • Direct Connect Configuration - HI 6300 Series Instrument
    • Ethernet-UDP
    • Modbus-RTU (over RS-485)
      • Wiring Pinout
      • Modbus Setup
      • Modbus Functions
      • Modbus Registers
      • Network Command Interface
  • Communications Parameters for the HI 6310 Only
    • Printer (over RS-232)
    • USB Memory Stick
    • Analog 4-20mA
  • Chapter 5
• Instrument Configuration
  • Using the Home Page to set Parameters
  • Using the Front Panel Display Menus to Set Parameters
    • Front Panel Display
    • The Five Button Command Cluster
    • Using the Mode, Zero, and Tare buttons
      • Entering Numeric and Alphanumeric Values
    • Commands and Parameters
    • Calibration Menu
      • C2 (eCal) Commands and Parameters
      • Ref Weight Parameter
      • Sensitivity Parameter
    • Hard Cal Commands and Parameters
      • Cal Lo Weight Parameter
      • Cal Tolerance Parameter
      • Span Weight Parameter
      • Cal Date Parameter
    • Communication Menu
      • HI 6310 Only
      • Ethernet TCP/IP Commands and Parameters
      • Enable DHCP Parameter
      • Fixed IP Parameter
      • Mask Address Parameter
      • Gateway Address Parameter
      • DNS Server Parameter
      • Ethernet UDP Parameters
      • Hardy Port Parameter
    • Modbus-RTU Commands and Parameters
      • Slave Address Parameter
    • Printer Command Parameters
    • USB Memory Stick Parameters
    • 4-20 mA Communications Commands and Parameters
      • Weight Source Parameter
  • Diagnostics Parameter Menu
    • See the Chapter 9 for further information on Diagnostics.
  • Display Parameter Menu
    • Backlight Parameter
    • Power Saving Parameters
    • Auto Enable Parameter
    • Wait Time Parameter
    • Set Background Parameter
    • Set Foreground Parameter
    • Split Screen Parameters and Commands
    • Filter Parameter Menu
      • NumAverages Parameter
      • WAVERSAVER® Parameter
    • Information Page
    • Language Parameter Menu
  • Operations Parameter Menu
    • Tare Operations Commands and Parameters
      • Tare Amount Parameter
      • Note that on the Web page, the value will appear on the Operations web page under Tare Operations.
      • Tare Offset Parameter
      • Tare Command
    • Zero Operations Commands and Parameters
      • Zero Tolerance Parameter
      • Zero Amount Parameter
      • Zero Command
    • The Zero Command will fail if the scale is in motion
      • Auto Mode
    • Count Operations Parameters and Commands
  • Security Parameter Menu
    • The Calibration Lock Parameters
      • Calibration Lock Parameter
      • Calibration Password Parameter
    • The Configuration Lock Parameters
      • Configuration Lock Parameter
      • Configuration Password Parameter
    • The Display Lock Parameters
      • Display Lock Parameter
      • Display Password Parameter
    • The Keypad Lock Parameters
      • Keypad Lock Parameter
      • Keypad Password Parameter
    • The Read Only Lock Parameters
      • Read Only Lock Parameter
      • Read Only Password Parameter
  • Setup Parameter Menu
    • Capacity Parameter
    • Decimal Point Parameter
    • Graduation Size Parameter
    • Instrument ID Parameter
    • Motion Tolerance Parameter
    • Operator ID Parameter
    • Unit (of Measure) Parameter
  • Chapter 6
• Calibration
  • Pre-Calibration Procedures
  • Electrical Check Procedures
    • Load Cell/Point Input/Output Measurements
    • Load Check
  • C2 & eCAL Electronic Calibration
    • Gravitation Correction
    • C2 and eCAL Calibration from the Web Page
    • C2 Calibration from the Front Panel
  • Hard Calibration
    • Hard Calibration from the Web page
    • Hard Calibration from the Front Panel
  • Chapter 7
• Operation
  • Getting Started
    • Mode Button
    • Zero Operation
    • Tare Operation
    • Auto Mode Tracking – Disabled (Default)
    • Auto Mode Tracking – Enabled
    • If the instrument is in NET mode when the ZERO command is sent over communications, the display will automatically switch to showing GROSS mode after the ZERO command is sent.
    • Count Operations
  • Split Screen Mode
    • Making Longer Display Interface Cables
  • Chapter 8
• Security
  • Display Security Options
  • The Display Lock
  • The Keypad Lock
  • The Configuration Lock
  • The Read Only, Security & Calibration Locks
  • Modifying the Security Parameters
  • Modifying the Calibration Parameters
  • Modifying the Read Only Parameters
• Chapter 9 Troubleshooting
  • Disassembly and Reassembly Notes, Warnings & Cautions
  • Error Messages
  • Trouble Shooting Using Integrated Technician (IT®)
    • Stability Test ALL
    • PASS/FAIL and Stability Test
      • WAVERSAVER TEST
  • Weight and Voltage ALL
    • Weight
    • RTZ (Return to Zero) Test
    • IT Test
      • Sensor Number
  • General Troubleshooting Flow Chart Index
  • A - Guideline Instability: Electrical and Mechanical review.
  • A1. Checking for Unstable Components in a Weighing System
  • B. Guidelines for Electrical, Mechanical or Configuration Issues
  • B1 - Guidelines to Verify Electrical Installation
  • B2 - Guidelines to Verify Mechanical Installation
  • B3 - Guidelines to Verify Configuration/Filter Settings to Improve Stability
  • C - Integrated Technician and Stability Test Overview
  • E Testing for Non-Return to Zero (System with IT Summing Card.)
  • F. Verify Individual Load Sensor Millivolt Output readings
  • G- Calibration Errors When Performing the Calibration
  • H. Mechanical Installation
  • J- Electrical Inspection
  • K - Installation Check Points
  • M. Weight Processor’s Front Display is Blank or Locked
  • N. Analog Out (HI 6310 Only)
  • Tests and Diagnostics
    • Parameters
  • System and Load Cell Tests
    • Overview of Typical Load Cell System
    • INTEGRATED TECHNICIAN
      • Stability Test
      • Weight and Voltage Tests
• Index