GE GTWN5550DWW - Manual (Page 5)

GEAppliances.com
Options
Autosoak
This option begins with a brief agitation, soaks for a specified period of time, then moves through the rest of the cycle automatically. On
some models, this option is located on the Cycle Selector knob.
Extra Rinse
When you use extra detergent or bleach to clean heavily soiled clothes, use the Extra Rinse option to better remove additional residues.
Eabric Softener
Set this option when adding fabric softener to the washer or to select the enhanced Power Rinse.
NOTE: Do not use fabric softener dispensing balls with this washer. They do not work correctly in high efficiency washers.
Deiay Wash
On some models, os the Delay Wash pod is repeatedly pressed, the delay time sets to 30 minutes, 1 hour, 3 hours, 5 hours, 9 hours, and
bock to clear (0 minutes).
On other models, os the Delay Wash pod is repeatedly pressed, the delay time sets to 2 hours, 4 hours, 8 hours, and bock to clear (0 hours).
For all models, if the Delay Wash pod is pressed for 3 seconds, it clears (regardless of the delay time).
Signal
Use the Signal pod to change the volume of the end of cycle signal. Press the pod until you reach the desired volume or off.
Settings
Individual settings for agitation [Soil], water temperature [Temp], and spin [Spin] con be set from the minimum (lowest in column) to
maximum (highest in column). In general, the higher up the column, the more energy will be used.
My Settings (on some models}
As the cycle selector knob is turned, the Soil, Temp and Spin settings change to automatic pre-set default settings. If you desire a different
setting, press the appropriate pod(s). Then press and hold the My Settings pod for 3 seconds and the washer will "remember" these settings
for that Knob Selection. In the future, when you turn the selector knob to that cycle, your settings will be automatically recoiled. NOTE; Signal
volume cannot be set for
My Settings.
Power
Press to "woke up" the display. If the display is active, press to put the washer into idle mode.
NOTE: Pressing POWER does not disconnect the appliance from the power supply.
Start
Press Start to begin the cycle. NOTE; The lid must be closed for the washer to fill and the cycle to start. Pressing Start again will Pause the
cycle and the Cycle indicator light will blink.
To continue the cycle, press Start again or close the lid. If machine is paused more than 24 hours, the cycle will be cancelled. To stop the
cycle, hold the pod for 3 seconds. If water remains in the machine, select the Drain & Spin cycle to drain tub and spin water out of the
washer tub.
Raising the lid will stop agitation or spin action but does not pause the cycle.
eWash (on some models)
When the eWash pod is pressed, the cycle changes to its most energy efficient settings and all of the eMonitor lights will light to indicate
that the most efficient settings ore on. If you change settings, the number of eMon/ior lights will decrease (or increase) to indicate decreased
or increased energy efficiency settings.
Display (on some models)
The display shows the approximate time remaining until the end of the cycle.
NOTE: The cycle time is affected by how long it takes the washer to fill. This depends on the water pressure in your home. The "smart" timer
"learns" the amount of time it takes to fill your washer and adjusts the total time accordingly.
In addition, this display will, "scroll" the washer status:
• bALANCING Start of rebalancing cycle to redistribute clothes. Stops after rebalancing is complete.
• dELAY When Delayed Wash is initiated. Replaced with estimated time when cycle starts.
• End End of current cycle.
• EILL For the first 45 seconds of a fill, the estimated end of cycle time is displayed. For the rest of the fill time, "FILL" is scrolled
until the fill completes.
• LID Cycle stopped because lid is open. Close the lid.
• PAUSE Cycle paused because the Start/Pause pod was pressed and the washer was set to Pause. Press Start pod again to
restart the cycle.
Indicator lights
Five LED lights indicate the current washer status moving from left to right os the cycle progresses.
DSM Demand Side Management (on some models) - When connected to your power company's rote monitoring system, the washer will
automatically delay storting if the rotes ore high/criticol. An "ES" will be displayed and the selected cycle will start after 4 hours or when
the rotes drop to low/medium, whichever comes first. If the rotes ore
not high/criticol, the selected cycle will start immediately.