Kenwood Preset Remote Control - Manual (Page 6)

I Preparing for automata operatiom
'$ (MACRO play)
The macro play function allows you to set the remote to control several
components in succession. After completing this setup, you can perform
a series of operations automatically. Enter the setup codes for the
components you want to control beforehand.
MACRO
During opration, make sure you start the next step within 8
seconds of completing the previous one. if more than 8
seconds elapses between any two steps, the remote control
unit exits from the MACRO play mode.
O IVlBke a plan of the macro play you want to Setup.
The order of the operations may be fairly complex and you may
not be remerriber all of the necessary commands during the
setup procedure.
Use the space provided below to write down the operations in
the order you are going to enter them.
* Up to 20 steps can be memorized for each macro.
0 0
0 0
0 0
0
0 0
0 0
0 0
0 0
0 0
0 ®
> The example below shows the plan for step O {which occupies a total
of 6 steps):
(D TV 4. AV. POWER 2 steps
(D FUNCTION SHIFT + 3 2 steps
<S) MOVIE 1 steps
(D AV, POWER 1 steps
Total 6 steps
' If you attempt to store more than 20 steps, “Fiji 1" appears and exit
the macro programming mode,
' Enter channel numbers (for the monitor TV, etc.) exactly as you would
using the original remote.
• V№en you select the input by using the MUSIC, MOVIE, or TV key,
it is count 1 step even if you press these keys several times.
GeUing the most from iroar remote pohiM
O Pfsss the MUSIC, MOViC, or JV key to select the macro
location. (MACR01, 2, and 3 respectively)
* You can store up to 3 different macros, one at each key;
MOVIE ^ "MHaiiO 1", MUSIC 'TIRCED 2", TV "HFCiCi 3"
*The light flashes once when you select the macro location.
* Pressing a key other than MUSIC. MOVIE, or TV cancels the macro
program mode.
r -------------- N
!-'« cr : oi
V. ;
When MOVIE is pressed
O Press the keys to be operated in order.
EXAMPLE:
This example shows you how to create a macro that; turns on the TV,
sets the TV to the appropriate input, selects the receiver's input selector
to LD, and turns on the LD player. All you have to do is insert the laser
disc!
© Press the TV key, then press the AV.POWER i/d) key to turn
on the TV,
0 Press the F. SHIFT key, then press the "3" (INPUT SEL.) key
to set the TV to the appropriate video Input.
® Press the MOVIE key to select the LD player registered at
VIDEO 2.
® Press the AV.POVI/ER i/<!) key to turn on the LD player.
» Make sure you start the next operation within 8 seconds of complet­
ing the previous one. If more than 8 seconds elapses between any two
steps, exit the macro programming mode.
* in order to allow verification of the remote control mode, the name of
the selected input appears in the receiver's display when the MUSIC,
MOVIE, or TV key is pressed. When the MUSIC or MOVIE key is
pressed the receiver's input also changes.
O Press the MACRO key so that the light Hashes twice.
® The macro is stored at the locations specified in step £3. If another
macro was previously stored at the same iocation, it is erased.
Repeat steps O through 0 to program up to 3 macros.
This completes the macro programming procedure.
1 ^ Press and hold the MACRO key for more than 2 seconds.
• "MflCFlG flEHORV" appears in the display.
ili
itili
MfrjRO NBIOiRV