Kenwood B60-0763-00 - Manual (Page 23)

Tuner section
Symptom Cause Remedy
Radio stations cannot be received. • No antenna is connected.
• The broadcast band is not set properly.
•
The frequency of the desired station is
not tuned.
• Connect an antenna.
• Set the broadcast band properly.
• Tune the frequency of the desired station.
A station which was preset cannot be
received by pressing the corresponding
numeric key. • The preset station belongs to a frequency
that cannot be received.
• The preset memory was cleared because
the power cord had been unplugged for a
long period of time.
• Preset a station with a receivable
frequency.
• Preset the station again.
Interference. • Noise due to ignition noise of an
automobile.
• Noise due to an influence from an electric
appliance.
• Noise due to a nearby TV set.
• Install the outdoor antenna apart from the
road.
• Turn off the power of the appliance.
• Install the system more apart from the TV
set.
Notes:
1. This system is microprocessor-controlled, so malfunction may occur due to external noise or interference noise. In such a case, unplug the
power cord, plug it and turn power on again.
2. Do not use contact cleaners because it could cause a malfunction. Be specially careful against contact cleaners containing oil, for they may
deform the plastic components.
Speaker protection circuitry
If the speaker cords are short-circuited, the speaker protection
circuitry is activated and the sound is muted. If this occurs,
switch the POWER key to OFF, remove the short-circuit from
the speaker cords, and switch the POWER key to ON again.
Normal operation wili resume.
Manufactured under license from Dolby Laboratories
Licensing Corporation. Additionally licensed under one or
more of the following patents: U.S. numbers 3,632,886,
3,746,792 and 3,959,590: Canadian numbers 1,004,603 and
1,037,877.
"Dolby" and the double-D symbol □□ are trademarks of
Dolby Laboratories Licensing Corporation.
For the U.S.A.
FCC WARNING:
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful
interference unless the modifications are explicitly approved in the instruction manual. The user could lose the authority to
operate this equipment if an unauthorized change or modification is made.
Strömbrytarens POWER beredskapsläge
Indikatorn STAND BY lands after nätkabelns anslutning till all
vägguttag, oavsett strömbrytarens POWER till/frànslag. Detta
anger att en liten mängd ström leds till komponenten som stöd
för minnesinnehállet. Detta läge kallas för beredskapsläget.
Strömbrytaren pà fjärrkontrollen kan användas för att slà pà och
av strömmen sä länge indikatorn STAND BY lyser.
Virtanappäimen (POWER) valmiustiia (STAND BY)
Kun laitteen verkkojohto on liitetty pistorasiaan, valmiustilan
merkkivalo
syttyy riippumatta virtanäppäimen (POWER)
ásennosla (ON/OFF). Merkkivalo osoittaa, että laitteessa on
hieman virtaa muistin sisältöjen ylläpitoa varíen. Tätä tilaa
kutsutaan valmiustilaksi. Kun valmiustilan merkkivalo (STAND
BY)
palaa, laitteen virta voidaan kytkeä ja katkaista
kaukosäätimellä.
Afbrydertastens (POWER) STAND BY funktion
När apparatets str(|>mledning er tilsluttet en stikkontakt, lyser
STAND BY Indikatoren, uanset om der er taendt ved afbryderen
pä apparatet eher ej. Det angiver, at apparatet bliver forsynet
med en ganske lille maengde stri|)m til opret-holdelse af
hukommelsens indhold. Denne funktion kaldes STAND BY. När
STAND BY Indikatoren er taendt, kan str<|)mmen til apparatet släs
til og fra med fjernstyringsenheden.
PÄ/AV-knappens Stand-by funksjon
När str(|>mledningen til dette anlegget er satt i en
vekselstr(|>mskontakt, vii STAND-BY indikatorlampen lyse enten
PÀ/AV-knappen er pä- eller avsiätt. Dette betyr at en viss
mengde str<|>m tilf(|)res anlegget slik at innholdet i minnet ikke
gär tapt. Denne funksjonen kalles Stand-by. När indikatorlampen
for STAND-BY er tent, kan str<|)mmen släs PÄ/AV fra
fjernkontrollen.
KR-V6040 (En) 23