Kenwood 1070VR - Manual (Page 11)

Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of
convenient system control operations.
There are two KENWOOD system control modes. Make connections according to the groups of terminal symbols shown ^
below.
iXSB] Mode ; loia you ooiTibifio [X5], OiSB", and fXi] Lsniiuials
SL1Q Mode : for GLIB terminals only
This unit is compatible with both [XSSj and 1SL16] modes. It comes from the factory set to the [SL16| mode. To switch to the [XS81 mode, follow
the instructions in "3WITCi IlMG mOM [GL10I TO [XGGl" below.
EXAMPLE: [XS8] mode connections
The underlined poitiori represents the setting of the svsiem cor^trol rt^ode,
EXAMPLE: [SL16] mode connections
The underlined portion represents the setting of the system conlroi mode,
[SL16] rXS8i
[SL16]
rSL16iiXSirXS81 rXRi
[SL161 [XSl ÌXS8I
[XS]
Receiver
MD recorder
Cassette deck
CD player
Record player
SYSTEM
CONTROL
cord
ÌSL16I [XS8]
ISL16Ì
fSLiei IXS] [XS8] [XR]
rSLiei [XS] [XS8]
[XS]
Receiver
MD recorder
Cassette deck
CD player
D
SYSTErvI
CONTROL
cord
Record player
• In order to take advantage of fhe system control operations, the components must be connected to the correct jacks. To use a CD player it must
be connected to the CD jacks. To use a cassette deck tor MD recorder! it must be connected to the TAPE/MD jacks. When using more than one
CD player (etc.) only the one connected to the specified jacks may be connected for system control.
• Some CD players and cassette decks are not compatible with the ¡SLl 6] system control mode. Be sure to use the IXS81 system control mode
when making system connections with equipment that is not [SLl 6| compatible.
• Some MD players are not system control compatible. You cannot make system control connections to this kind of equipment.
1. [SL16I equipment cannot be Combined with |XR], [XS], and |XS8| equipment for system operations If your
equipment consists of fhis kind of combination, please do not connect any system control cords. Even without
system control cords, normal operations can be carried out without effecting performance.
2. Do not connect system control cords to any components other than those specified by KENWOOD, It may
cause a malfunction and damage your equipment.
3. Be sure the system control plugs are inserted all the way in to the system control terminals.
SYSTEM CONTROL OPERATIONS SWITCHING FROM [SUB] TO [XS8]
Remote Control You can easily change the system control mode by adjusting the |
, Lets you operate this unit with the system remote supplied with the position of the SYSTEM CONTROL switch on the rear panel, j
receiver. Do this operation after completing all connections. 1
Automatic Operation {except [XR] equipment)
When you start playback from a source connponent, the input selector
For[SL16l SL 16 XS a ForlXBBl
m on this unit switches to that component automatically. i
È 1
1 Synchronized Recording (except [XRI equipment!
:
• This operation will not effect items stored in the memory.
Lets you synchronize recording with the start of playback when 1 • After switching the system control mode, turn the power off a nd
>. recording from CD, MD or analog discs.
1
I
then on once to confirm the new setting.
I 1
Registering setup codes for KENWOOD audio components
• Once you finish making the system connections, be sure to register the appropriate setup cocie for each component. -i3?^
• Ifyojown remote controllable KENWOOD audio components that are not compatible with system control (or cannot be combined with your other
system control components), registering the setup code enables you to control those components using the remote control supplied with this
unit (without connecting system control cords). To register setup codes for your remote controllable KENWOOD audio components, see
■Registering setup codes for other components".