Toshiba SD-V290-S-TU - Manual (Page 16)

Before Operation - VCR Part (Continued)
Setting the VCR Setup Menu
f Press VCR MENU and the MAIN menu will
appear.
M Press A/T to select the SETUP menu, then
m press ENTER.
The SETUP menu will appear.
CLOCK
1^ PROQRAM
13 TUNING
1^ SETUP.
□□SELECT no ENTER
TO EXIT PRESS CZU
LANGUAGE SELECT:ENGLISH
AUDIO MODE: HI-FI
BROADCAST TYPE: STEREO
AUDIO OUTPUT: STEREO
□□SELECT □□ ADJUST i
TO EXIT PRESS 11:1®#
f Press A/T to choose a desired option on the
SETUP menu. Then press “^^l/^^to choose a
desired setting.
FUNCTION OSD
The on-screen display of this DVD+VCR can be turned on or off.
• FUNCTION OSD can be switched between ON and OFF by
pressing
LANGUAGE SELECT
The on-screen programming of this DVD+VCR can be
displayed in either English, Spanish, or French.
• LANGUAGE SELECT can be switched among ENGLISH,
SPANISH and FRENCH by pressing
AUDIO MODE
The DVD+VCR has two separate audio playback systems, the
high quality VHS Hi-Fi system and standard NORMAL mono sys­
tem. The same audio is generally recorded on both systems. The
VHS Hi-Fi system plays on separate (left and right) channels, and
the NORMAL system plays monaural sound. The normal track is
always played so the cassette can be played on a DVD+VCR that
does not have VHS Hi-Fi.
• AUDIO MODE can be switched between Hi-Fi and
NORMAL by pressing -A/P-.
BROADCAST TYPE (STEREO/SAP/MONO)
Multichannel Television Sound (MTS) carries stereo and/or
Second Audio Program (SAP) bilingual signals. Set this display to
the desired position when both MTS stereo and SAP signals are
received. When only one of the MTS signal is received, the
DVD+VCR automatically selects the corresponding receiving
mode (Stereo or SAP) regardless of the selected position. For
normal operation, the display should be in the STEREO position.
The DVD+VCR will then record a STEREO program when available,
and record a mono program IF the program is NOT IN STEREO.
For weak STEREO and/or SAP broadcasts, changing the dis­
play to mono may give clearer sound.
• BROADCAST TYPE can be switched among STEREO, SAP,
and MONO by pressing ^</* *..
AUDIO OUTPUT (STEREO/LEFT^iGHT)
Used during playback [when AUDIO MODE (HI-FI/NORMAL) is
in HI-FI position] for selecting the audio output signals from the
AUDIO OUT terminals (L ch and R ch), and RF.OUT,
This display setting should normally be left in the stereo posi­
tion, so that when a stereo tape is played, the stereo sound will
be heard through the left and right channels, if a mono tape is
played and the audio output is set to stereo, the same mono
sound will be heard from both left and right channels.
• AUDIO OUTPUT can be switched among STEREO, LEFT,
and RIGHT by pressing
Press VCR MENU when finished.
Channel Selection
This DVD+VCR is equipped with a frequency
synthesized tuner capable of receiving up to 181
channels. These include VHF channels 2-13, UHF
channels 14-69 and CATV channels 1-125.
Preparation:
• Connect the DVD+VCR to the desired type of antenna or
cable TV system, as shown in Connecting Antenna/Cable TV
to DVD+VCR on page 11.
AUTO CHANNEL PROGRAMMING
f Press VCR MENU and the MAIN menu will
appear.
f Press Ajw to select the TUNING menu, then
press ENTER.
The TUNING menu will appear.
■ n
1 AUTO CHANNEL SET 1
TUNING BAND: TV
CH. ADD/DEL; CH. 2 ADD
SOURCE SELECT: TUNER
■ Press T to choose the SOURCE SELECT option,
then press -4/1^ to select TUNER.
Press repeatedly to switch among TUNER, LINE1
and LINE2.
' Press A/T to choose the AUTO CHANNEL SET
option, then press to set the channel.
The tuner will automatically cycle through all
available channels in the area and place them in
the tuner’s memory.
After the AUTO CHANNEL SET PROCEEDING is
complete, make sure the TUNING BAND is set
appropriately {TV or CATV) by pressing A/T and
choosing the correct TUNING BAND (TV or
CATV) by pressing using the TUNING
menu.
Remember, TV is for the air antenna reception,
CATV is for cable or wireless cable connection,
i Press VCR MENU to return to the TV screen.
Use CH/TRK (+/-) or CHANNEL (A/T) on the
front panel to cycle the DVD+VCR through the
channels in memory.
TO ADD OR ERASE CHANNELS FROM MEMORY
This feature allows you to add or erase channels from
memory manually.
1 Press T to choose the CH. ADD/DEL option on the
TUNING menu. Press -4(/l^ to select a channel to
add or erase.
2 Press ENTER to add or erase the channel.
Repeat steps 1 and 2 to add or erase channels.
3 Press VCR MENU to return to the TV screen.
1-18