Crosman DCR75F - Manual

DCR75/F
6mm BB AEG
OWNER’S MANUAL
READ ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL BEFORE USING THIS AIRSOFT GUN
Crosman Corporation
7629 Routes 5 & 20
Bloomfield, NY 14469
www.crosman.com
1-800-724-7486
Made in the Taiwan. DC75-515
THIS IS NOT A TOY. ADULT SUPERVISION REQUIRED. MISUSE OR CARELESS USE MAY CAUSE SERIOUS INJURY, ESPECIALLY TO THE
EYE. EYE PROTECTION MUST BE USED BY THE USER AND ANY PERSON WITHIN RANGE. MAY BE DANGEROUS UP TO 100 YARDS (91.44 METERS). READ
OWNER’S MANUAL BEFORE USING.
Notice: Read this owner’s manual completely. And remember, this airsoft gun is not a toy. Treat it with the same respect you would a firearm. Always carefully follow the safety
instructions found in this owner’s manual and keep this manual in a safe place for future use.
YOU AND OTHERS WITH YOU SHOULD ALWAYS WEAR SHOOTING GLASSES TO PROTECT YOUR EYES.
BUYER AND USER HAVE THE DUTY TO OBEY ALL LAWS REGARDING THE USE AND OWNERSHIP OF THIS AIRSOFT GUN.
DO NOT BRANDISH OR DISPLAY THIS AIRSOFT GUN IN PUBLIC – IT MAY CONFUSE PEOPLE AND MAY BE A CRIME. POLICE AND
OTHERS MAY THINk IT IS A FIREARM. DO NOT CHANGE THE COLORATION AND MARkINGS TO MAkE IT LOOk MORE LIkE A FIREARM. THAT IS DANGEROUS
AND MAY BE A CRIME.
THIS PRODUCT CONTAINS ONE OR MORE CHEMICALS kNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH
DEFECTS (OR OTHER REPRODUCTIVE HARM).
If you have any questions regarding your AIRSOFT GUN, please contact Crosman at 1-800-724-7486, 585-657-6161 or www.crosman.com.
1. Safety First
• ALWAYS treat the airsoft gun gun as though it is loaded and ready to fire and with the same respect you would a firearm.
• ALWAYS store the airsoft gun unloaded.
• ALWAYS store the airsoft gun away from children.
• ALWAYS aim in a SAFE DIRECTION.
• ALWAYS keep the muzzle of the airsoft gun pointed in a SAFE DIRECTION.
• ALWAYS keep your finger off the trigger and out of the trigger guard until ready to shoot.
• ALWAYS keep the airsoft gun “ON SAFE” until you are ready to shoot (see section 3A).
• ALWAYS check to see if the airsoft gun is “ON SAFE” (see section 3A) and unloaded when getting it from another person.
• ALWAYS have you and others wear shooting glasses to protect your eyes.
• ALWAYS wear shooting glasses over eye glasses if your prescription or reading glasses are not safety glasses.
• ALWAYS place the backstop in a location that will be safe should the backstop fail.
• ALWAYS check your backstop for wear before and after each use. All backstops are subject to wear and will eventually fail. Replace your backstop if
the surface is worn or damaged, or if a ricochet occurs.
• ALWAYS use the proper size BB in your airsoft gun Check the markings on your airsoft gun to verify the BB size- 6mm.
• NEVER reuse ammunition.
• NEVER shoot at hard surfaces or at the surface of water. The BB may bounce off or ricochet and hit someone or something you had not intended
to hit.
• NEVER point the airsoft gun at any person or at anything you do not intend to shoot.
2. LEARNING THE PARTS OF YOUR AIRSOFT GUN
Learning the names of the parts of your new airsoft gun will help you to understand your owner’s manual. Use this manual to increase your enjoyment of this airsoft gun.
A. Muzzle
B. Charging Handle
C. Retractable Stock
D. Stock Release lever
E. Trigger
F. Trigger Guard
G. Magazine
H. Magazine Release Button
I. Safety (see Fig. 2)
J. Forearm/Hand Guard
3. OPERATING THE SAFETY
A. TO PUT THE AIRSOFT GUN “ON SAFE:”
• Locate the safety on the left side of the airsoft gun.
• Turn the safety lever to “SAFE” for “ON SAFE. (Fig 2A). The safety is not “ON SAFE” unless it is pointing to “SAFE”. keep the airsoft gun in the “ON SAFE” position until you are actu-
ally ready to shoot. Then turn the safety to the “OFF SAFE” position.
Like all mechanical devices, an airsoft gun safety can fail. Even when the safety is “ON SAFE”, you should continue to handle the airsoft gun safely.
B. TO TAKE THE AIRSOFT GUN “OFF SAFE”
NOTE: This airsoft gun fires in semi or full auto-mode. Full auto means it will continue to fire plastic
BBs as long as you hold the trigger. Semi-auto means you will have to pull the trigger each time you want to fire a shot.
• Locate the safety on the left side of the receiver.
• Turn the lever to “SEMI” for semi-auto mode. (Fig. 2b)
• Turn the lever to “AUTO” for full auto mode. (Fig. 2c)
• The airsoft gun is “OFF SAFE” and ready to fire when pointing to either “semi” or “auto.”
NEVER point the airsoft gun at any person. NEVER point the airsoft gun at anything you do not intend to shoot.
4. CHARGING, LOADING AND REMOVING THE BATTERY
A. CHARGING THE BATTERY
NOTE: The battery charging time is 4-6 hours prior to initial use. To prolong battery life and maintain the best shooting performance rest the gun for 5-10 minutes after firing about 500
rounds. For optimum performance completely use up the battery before recharging. DO NOT OVERCHARGE THE BATTERY. UNPLUG THE BATTERY CHARGER WHEN NOT IN USE.
BATTERY COVER TABS
B. LOADING THE BATTERY
1. Make sure the airsoft gun is “ON SAFE” (see 2A) and is UNLOADED.
2. Point the airsoft gun in a SAFE DIRECTION.
3. Remove butt plate cover from rear of the stock by depressing the two tabs on both sides of the stock.
4. Insert the two battery cells on each side of the buffer tube as shown.
5. Connect the battery connector to the gun connector by lining up the electrical tabs.
6. Place the connectors inside the buffer tube.
7. Snap the butt place back into place as shown.
C. REMOVING THE BATTERY
1. Make sure the airsoft gun is “ON SAFE” (see 2A) and UNLOADED.
2. Point the airsoft gun in a SAFE DIRECTION.
3. Remove butt plate cover from rear of the stock by depressing the two tabs on both sides of the stock.
4. Remove the two battery cells by slowly sliding the cells out of the buffer tube as shown.
5. Disconnect the battery connector by depressing the electrical tabs.
6. Replace the gun connector and electrical wires inside the buffer tube.
7. Snap the butt place back into place as shown.
5. LOADING AND UNLOADING PLASTIC BBS
A. LOADING
Only use 6 mm plastic BBs in this airsoft gun. Use of any other ammunition can cause injury to you or damage to the airsoft gun. We recommend
using Crosman, Duty Calls, or GameFace BBs. Use of any other ammunition can cause injury to you or damage to the airsoft gun.
MAkE SURE THE AIRSOFT GUN IS “ON SAFE” (SECTION 2A).
1. Point the airsoft gun in a SAFE DIRECTION.
2. While supporting the BB magazine, push the magazine release button
and remove the magazine.
3. Slide open the magazine cap door.
4. Insert 6 mm plastic BBs.
5. Close the magazine cap door.
6. Insert the loaded magazine back into the airsoft gun.
7. Rotate the wind up wheel to draw plastic BBs up into the ready tube.
Wind the wheel 50 to 75 turns for optimum performance.
NOTE: IT IS IMPORTANT TO PUT THE MAGAZINE IN THE GUN PRIOR TO WINDING TO HELP
AVOID JAMS.
Winding before putting into the gun can cause a jam.
B. UNLOADING PLASTIC BBs
1. Make sure the airsoft gun is “ON SAFE” (section 2A).
2. Point the airsoft gun in a SAFE DIRECTION.
3. While supporting the BB magazine, push the magazine release lever forward and remove the magazine.
4. Slide open the magazine cap door behind the ready tube.
5. Pour out BBs.
6. To release the BBs in the ready tube, point the clip down in a safe direction and push back and hold the BB retainer button. NOTE: BBs will release rapidly.
7. Rotate the wind up wheel to draw BBs into the ready tube.
8. Repeat the above steps until all the BBs are out of the magazine.
9. Close the magazine cap.
Never assume that because the airsoft gun no longer fires a BB and/or the loading chamber is removed, that a BB is not lodged in the barrel. Always treat the airsoft gun as though it is
loaded and with the same respect you would a firearm.
EVEN THOUGH YOU GO THROUGH THE UNLOADING PROCEDURE, CONTINUE TO TREAT THE AIRSOFT GUN AS THOUGH IT WERE
LOADED. DO NOT POINT AT ANYTHING YOU DO NOT INTEND TO SHOOT.
6. USING THE HOP-UP MODE
Your airsoft gun is manufactured with an adjustable hop-up system. The purpose of this system is to change the spin on the BB as it leaves the muzzle, allowing you to adapt your shot
for different distances.
1. Pull out and hold the charging handle to open the ejection port cover.
2. Use finger to hold open ejector port door
3. Turn the hop-up adjustment dial clockwise for more spin, counter-clockwise for less spin.
7. ADJUSTING THE STOCK
1. Your airsoft gun is shipped with the stock in the closed position and is capable of adjusting to different lengths.
2. Before adjusting the stock make sure your airsoft gun is “ON SAFE”, (see section 2A) and pointed in a SAFE DIRECTION.
3. Push the stock release lever and adjust the stock until it locks into the desired position.
8. FIRING SAFELY AND ADJUSTING THE SIGHTS
A. FIRING SAFELY
1. You and others with you should always wear eye protection designed for airsoft to protect your eyes.
2. Always point your airsoft gun in a SAFE DIRECTION.
3. Do not shoot at hard surfaces or at the surface of water. The plastic BBs may bounce off or ricochet and hit someone or something you had not intended to hit.
4. DO NOT re-use plastic BBs because they could possibly cause damage to your airsoft gun.
5. Your airsoft gun is designed for target shooting and is suited for both indoor and outdoor use. Always remember to place your target carefully. THINk about what you
will hit if you miss the target.
B. ADJUSTING THE REAR SIGHT
1. The rear sight is adjustable for windage.
2. To adjust for windage, use the dial on the side of the sight.
3. Turn clockwise to move the point of impact to the right.
4. Turn counter-clockwise to move the point of impact to the left.
9. MAINTAINING YOUR AIRSOFT GUN
• DO NOT MODIFY OR ALTER YOUR AIRSOFT GUN. Attempts to modify the
airsoft gun in any way inconsistent with this manual may make your airsoft
gun unsafe to use, cause serious injury, especially to the eye and will void
the warranty.
• If you drop your airsoft gun, visually check to see that it works properly before
you use it again.
• If anything seems changed, like a shorter or weaker trigger pull, this may mean worn out or broken parts. Call Crosman customer service for assistance before using your airsoft
gun again.
A. How to clean the magazine
1. Remove magazine
2. Wipe down outside of magazine
3. Spray small amount of Crosman Nitro Lubricant oil into BB tube
4. Replace magazine
B. To clean the Airsoft gun barrel
1. Spray a cleaning patch with Crosman Nitro Lubricant oil.
2. With patch on rod, insert it into barrel to clean
3. Swab barrel 3-4 times
4. Repeat swabbing procedure with a dry patch
5. Barrel is clean when patches come out clean after dry swabbing.
C. Clearing a Jam
Never look down the end of barrel to see if a jam has been cleared.
1. Make sure the airsoft gun is “ON SAFE” and pointed in a SAFE DIRECTION.
2. Remove magazine.
3. Insert the tapered end of the cleaning rod into the barrel.
4. CAREFULLY and slowly apply more pressure until you push the BB out of the breech.
5. Reinstall the magazine and test gun.
SPECIFICATIONS
Mechanism Electronic Velocity Up to 300 fps with .2 g
Sights
Front: Flip-Up and removable
Sights Rear: Flip-Up and adjustable/removable
Length 30 to 31 inches
Caliber/Ammunition 6 mm Plastic BB Safety Lever
Capacity Up to 300 BBs Weight
DC75F - approximately 6 lbs.
DC75 - approximately 5 lbs.
PERFORMANCE: Many factors can affect velocity, including brand of projectile, type of projectile and barrel condition.
DO NOT RETURN THIS PRODUCT TO THE STORE.
Our customer service representatives will help. You can get answers to frequently asked questions at www.crosman.com or you can contact us directly at 1-800-7AIRGUN
(1-800-724-7486)
CUSTOMER SERVICE
If your airsoft gun is not functioning, we recommend that you call Crosman Corporation Customer service at 1-800- 724-7486 or 585-657-6161. (International customers should contact
their distributor.) DO NOT ATTEMPT TO DISASSEMBLE IT! If you take it apart you probably will not be able to reassemble it correctly. Crosman assumes no warranty responsibility under
such circumstances.
For optimum performance use Crosman ammunition only. Using other than Crosman branded ammunition may cause your product to malfunction and may void your warranty.
LIMITED 90 DAY WARRANTY
This product is warranted to the retail consumer for 90 days from date of retail purchase against defects in material and workmanship and is transferable.
WHAT IS COVERED
Replacement parts and labor. Transportation charges to consumer for repaired product.
WHAT IS NOT COVERED
Transportation charges to Crosman for product. Damages caused by abuse, modification or failure to perform normal maintenance. Any other expense. CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, OR INCIDENTAL EXPENSES, INCLUDING DAMAGE TO PROPERTY. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
WARRANTY CLAIMS
USA Customers: Attach your name, address, description of problem, phone number and copy of sales receipt to product. Package and return to Crosman Corporation, Routes 5 & 20,
Bloomfield, NY 14469.
International Customers: Please return product to your nearest distributor. If you do not know your distributor, please call 585-657-6161 and ask for our International Department
for assistance.
IMPLIED WARRANTIES
ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO 30 DAYS FROM DATE OF
RETAIL PURCHASE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
To the extent any provision of this warranty is prohibited by federal, state, or municipal law which cannot be preempted, it shall not be applicable. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state.
CROSMAN is a registered trademark of Crosman Corporation in the United States.