Philips AJ3840/10M - Manual (Page 2)

Controls Clock/Radio
m
3
«
(D
@
@
®
®
@
®
®
@
®
REPEAT ALARM button
CASSETTE compartment
ALARM RESET button
To switch off the alarm for 24 hours.
FUNCTION buttons
- RADIO CASSETTE ON button
To switch on the radio and to put the
cassette mode on standby
- OFF button
To switch the radio/cassette or alarm off.
CLOCK buttons
- TIME SET button
To set the time
- ALARM SET button
To set the alarm
- '+' SET button
To set the time/alarm fast forward
- SET button
To set the time/alarm slow backward
- SLUMBER button
To set/switch on the slumber time
PHONES O
Stereo headphone socket
Connection for headphones (not included)
TUNING control
For station selection
BAND switch
To select between FM, MW and LW (not for
all versions)
VOLUME control
To adjust the volume level
BATTERY compartment
CLOCK DISPLAY
ALARM 2 indicator ^
Indicates that alarm 2 is switched on
ALARM 1 indicator ^
Indicates that alarm 1 is switched on
ALARM 1 Selector
-
BUZZ - to be woken by the buzzer
- RAD/CASS - to be woken by the
radio/cassette
- OFF-To disable alarm 1
ALARM 2 Selector
- BUZZ - to be woken by the buzzer
- RAD/CASS - to be woken by the
radio/cassette
- OFF-To disable alarm 2
BRIGHTNESS control switch (Hi/Low)
To control the brightness of the clock display
CASSETTE buttons
- PLAY ►
To start playback
- REWIND •H
To fast-rewind the cassette
- FORWARD ►►
To fast-forward the cassette
- STOPB
To stop the playback
FM Antenna
Voltage selector (120V/240V)
(not all versions)
Mains supply
• Check that the mains voltage as shown on the
type plate (at the base of the set) corresponds
to your local mains voltage. If it does not,
consult your dealer or service organisation.
If the set is equiped with
a voltage selector, set
this selector to the local
mains voltage.
• Connect the mains lead
to the wall socket. The mains supply is now
connected. As soon as you insert the mains
plug into the wall socket, the figures on the
display will blink. This means that you must set
the correct time.
• To disconnect the set from the mains,
withdraw the mains plug from the wall socket.
Important note for users in the U.K;
When fitting a mains plug, follow the
instructions on page 8.
CLOCK____________________________________
Clock display ®
- The clock display shows the time. The display
also indicates whether you have switched on
the alarm. If alarm 1 is on, then ALARM 1 -S-
lights up in the display. For alarm 2 ALARM 2 * *
lights up in the display and for the dual alarm
both light up.
Setting the time
• Keep TIME button (S) pessed and at the same
time set the correct time by:
- pressing the '-i-' button ® or
- pressing the button ®
• Release the TIME button ®. The correct time
appears in the display
Antennas
- For FM reception there is an antenna wire at
the rear of the clock radio. This wire must be
extended and if necessary adjusted slightly in
order to obtain good reception.
- The AM/MW and LW antenna is built into the
clock radio. To obtain optimum reception you
may have to adjust the position of the clock
radio slightly.
LISTENING TO THE RADIO_______________
Switching the radio on/off
You can use this clock radio solely as a radio.
• Press the RADIO CASSETTE ON button ® to
switch on the radio. You may connect stereo
headphones with 3.5 mm plug to the socket HT
PHONES ®. The loudspeaker is then muted.
• Select the waveband using BAND switch @
• Tune to the desired station using TUNING
control knob @.
• Set the volume using VOLUME control ®.
• To switch off the radio, press the OFF button ®