Philips AZ 8101 - Manual (Page 5)

iONTROLS INSTALLATION
RONT PANEL - fig. 1 SUPPLY
!) VOLUME control
5 DBB bass button - press to increase the bass
response
D GRAPHIC EQUALIZER tone controls:
100 Hz - bass
I kHz (1 000 Hz) - mid-range
10 kHz (10 000 Hz)-treble
i) socket for stereo headphones
5 ON/OFF MODE selector
- to select the sound
source (or reproduction or recording
^ FM STEREO $ indicator
f)
BAND seiector
5 built-in mono MiCROPHONE
g TUNiNG knob
^ CD OPEN open the disc cover
1^ CD-player display:
TRACK track number
WAIT indicator
ERROR indicator 'E’
PROGRAM indicator ’P', track number is stored
FULL indicator 'F, memory is full
PAUSE
^ indicator
INTROSCAN # indicator
§) CD-player keyboard:
□ STOP
l> PLAY and DD PAUSE
PREVIOUS/NEXT play the M previous or next M
track
SEARCH go fast <W backward or forward И>
INTROSCAN play the beginning of each track
@ CD-player programming keyboard:
STORE store the displayed track number
DISPLAY display all stored track numbers
CLEAR erase the memory
TRACK display the next+ or previous— track
0 cassette deck keyboard:
■ STOP/EJECT
• RECORD - record
REWIND - fast rewind
>> F.FWD - fast forward wind
► PLAY
II PAUSE
BACK PANEL - fig. 2
Batteries
Whenever convenient, use AC mains supply if you
want to conserve battery life.
• Open the battery compartment (fig. 2).
• Insert as indicated eight (preferably Alkaline)
batteries, type R20, UM1 or D-cells.
• Remove the batteries if exhausted or if they will not
be used again for a long period.
The batteries are switohed off when the set is
connected to the mains. To change over to batteries,
pull out the plug from the AC MAINS socket
Mains
• Check if the mains voltage as shown on the type
plate corresponds to your local mains supply. If it
does not, consult your dealer or service organisa­
tion.
If the set is equipped with a VOLTAGE selector®, set
this selector to the local mains voltage.
• Connect the mains lead to the AC MAINS socket
® and the wall socket. The mains supply is now
switched on.
• To disconnect the set from the mains completely,
withdraw the mains plug from the wall socket.
Important note for users in U.K.:
When fitting a mains plug to the mains lead proceed as follows:
The wires in the mams lead are coloured in accordance with the
following code: B!ue»NeuUal. Bro'wnaUve.
These colours may not correspond with the colour markings identifying
the terminals in your plug, so proceed as follows:
Connect the Brown wire to the terminal marked L or coloured Red.
Connect the Blue wire to the terminal marked N or coloured Black.
No connection is necessary to the earth terminal.
Note: This apparatus must be protected by a 3 Amp Fuse if a 13 Amp
plug is used or. if any other type of plug is used, by a 5 Amp Fuse either
in the plug or adapter or at the distribution board. If in doubt consult
a qualified electrician.
CONNECTIONS - fig. 1-2 •
@ CD OUT sockets for high quality Compact Disc
reproduction through an amplifier, receiver,
recorder etc.
(g) VOLTAGE selector (not on all versions)
@ AC MAINS - socket for mains lead
Stereo headphone socket 0
For stereo headphones with 3.5 mm plug. Inserting
the plug will disconnect the loudspeakers.
CD Output sockets CD OUT @
Cinch-sockets for high quality Compact Disc re­
production
(not radio or cassette) through an am­
plifier, receiver, recorder, etc.
• Connect the CD OUT sockets @ to the tape
recorder input sockets REC IN. TAPE IN. UNE IN. AUX
or CD IN of the other set.
The CD OUT output signal is not affected by the
position of the controls VOLUME Q, GRAPHIC
EQUALIZER ® and DBB bass button
(®.